background image

Installation and service of this fi replace should be 

performed by qualifi ed personnel. Hearth & Home 

Technologies recommends NFI certifi ed profes-

sionals, or technicians supervised by an 

NFI certifi ed professional.

Fire Risk.

WARNING

For use with solid wood fuel only.

Other fuels may overfi re and generate 

poisonous gases (i.e. carbon monoxide).

Owner’s Manual

Care and Operation

INSTALLER:  Leave this manual with party responsible for use and operation.

OWNER:  Retain this manual for future reference.

EPA CERTIFIED WOODBURNING 

FIREPLACE

O-T  L

Tested and 

Listed by

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

C

US

Model(s):

NORTHSTAR-Bk

NORTHSTAR-GT

NORTHSTAR-NT

NOTICE: 

DO NOT

 discard this manual!

• 

DO NOT

 store or use gasoline or other fl am-

mable vapors and liquids in the vicinity of this 

or any other appliance.

• 

DO NOT

 overfi re. Overfi ring will void your 

warranty.

•  Comply with all minimum clearances to com-

bustibles as specifi ed. Failure to comply may 

cause house fi re.

   WARNING: If the information in these 

instructions is not followed exactly, a fi re 

or explosion may result causing property 

damage, personal injury, or death.

WARNING

HOT SURFACES

Glass and other surfaces are hot during 

operation AND cool down.

Hot glass will cause burns.

• 

DO NOT

 touch glass until it is cooled

•  NEVER allow children to touch glass

•  Keep children away

•  CAREFULLY  SUPERVISE  children  in  same  room  as 

fi replace.

•  Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other fl ammable 

materials.

•  Keep  clothing,  furniture,  draperies  and  other  fl ammable 

materials away.

Pour demander un exemplaire en 

français de ce Manuel 

du propriétaire, visitez www.

heatnglo.com/translations.

1

Heat & Glo • NorthStar Owner’s Manual • 480-2350 • Rev G • 05/15/14

Summary of Contents for NORTHSTAR-BK





































Reviews: