Heat&Glo NORTH STAR Installation & Operating Instructions Manual Download

Page: 30 / 36

480-1081B

10-05

North Star

EPA Certiﬁed Fireplace

10. Fan Replacement

Fan Cord Location

The North Star Fireplace comes standard

equipped with two fans, installed at the fac-

tory with electric access on the right side of

ﬁreplace (as you face it).

Fan Replacement Instructions

Power must be OFF prior to servicing!

The fan assembly may be accessed

before or after the ﬁreplace has been

installed.

Before Fireplace Installation:

1. Remove the 2 screws located at the

outside edge of the bottom panel as

show in Figure 30A.

2. Pull panel forward and remove from

ﬁreplace.

After Fireplace Installation:

1. Remove the ﬁrebrick from the bottom of

the ﬁreplace.

2. Remove the 2 screws from the access

panel in the ﬁrebox ﬂoor.

3. Pry up the access panel using the

screwdrive slot and completely remove

the panel.

Removing the Fan Assembly

1. Unplug the wire harness.

2. Lift fan off of studs and remove. Repeat for

second fan if necessary. See Figure 30B.

3. Inspect the gasket and ensure it is in good

condition.

4. Replace with new fan.

5. Reinstall bottom panel or ﬁrebox access

panel in reverse order as descibed above.

Screwdriver Slot

Screws

Remove 2 screws and pull panel forward

(Before fireplace installation)

After

fireplace

installation

Unplug wire harness

before removing fan

Figure 30B-Fan Motor

Figure 30-A Accessing Fan Motor

Summary of Contents for NORTH STAR





































Search results

Summary of Contents for NORTH STAR

Reviews:

Related manuals for NORTH STAR

Brands by name

Popular brands

Heat&Glo NORTH STAR, Installation & Operating Instructions Manual

Search results

Summary of Contents for NORTH STAR

Reviews:

Related manuals for NORTH STAR

Brands by name

Popular brands