Heat&Glo 6000CL-IPI-S Owner'S Manual Download

Page: 53 / 82

Heat & Glo • 6000CL-IPI-S, 6000CL-IPI-T, 8000CL-IPI-S 8000CL-IPI-T • 2165-900 Rev. X • 4/14

Finishing

A. Mantel and Wall Projections

WARNING! Risk of Fire!

Comply with all minimum clear-

ances as speci

ed. Framing closer than the minimums list-

ed must be constructed entirely of noncombustible materials
(i.e., steel studs, concrete board, etc.)

Figure 13.2 Clearances to Mantel Leg or Wall Projections

(Acceptable on both sides of opening)

Figure 13.1 Minimum Vertical and Maximum Horizontal
Dimensions

MEASUREMENTS FROM

TOP EDGE OF THE OPENING

2-1/2

TO CEILING

INTERIOR WALL

TOP VIEW

MANTEL LEG OR WALL PROJECTIONS

FIREPLACE OPENING

Note:

All

measurements
in inches.

minimum is ____, then

maximum is_____.

Inches

2-7/16 3-7/16 4-7/16 5-7/16 6-7/16 7-7/16

Millimeters

113

138

164

189

Inches



Millimeters

102

127



Note:

Measurement is taken from top of the opening,

NOT the top of the

replace.

B. Facing Material

• Metal front faces may be covered with non-combustible

materials only.

• Facing and/or

nishing materials must not interfere with

air

ow through louvers, operation of louvers or doors,

or access for service.

• Facing and/or

nishing materials must never overhang

into the glass opening.

• Observe all clearances when applying combustible

materials.

• Seal joints between the

nished wall and appliance top

and sides using a 300ºF minimum sealant. Refer to
Figure 13.3.

WARNING! Risk of Fire! DO NOT

apply combustible

materials beyond the minimum clearances. Comply with
all minimum clearances to combustibles as speci

ed in

this manual. Overlapping materials could ignite and will
interfere with proper operation of doors and louvers.

Figure 13.3 Noncombustible Facing Diagram

FACTORY-INSTALLED NON-COMBUSTIBLE BOARD

DO NOT REMOVE

6000

inches

39-3/4

millimeters

1010

1041

8000

inches

41-3/4

millimeters

1060

1219

Mantels - Combustible or Painted Surfaces

Mantel Legs or Wall Projections - Combustible or
Painted Surfaces

Summary of Contents for 6000CL-IPI-S



















































































Search results

Summary of Contents for 6000CL-IPI-S

Reviews:

Related manuals for 6000CL-IPI-S

Brands by name

Popular brands

Heat&Glo 6000CL-IPI-S, Owner'S Manual

Search results

Summary of Contents for 6000CL-IPI-S

Reviews:

Related manuals for 6000CL-IPI-S

Brands by name

Popular brands