Heat&Glo 6000C-IPI Owner'S Manual Download | Manualshive

Page: 65 / 85

background image

65

Heat & Glo • 6000C-IPI, 8000C-IPI • 2164-900 Rev. W • 8/14

Figure 14.5 Air Shutter

Figure 14.4 Fixed Glass Assembly

H. Fixed Glass Assembly

WARNING! Risk of Asphyxiation!

Handle

fi

xed glass

assembly with care. Inspect the gasket to ensure it is
undamaged and inspect the glass for cracks, chips or
scratches.

•

DO NOT

strike, slam or scratch glass.

•

DO NOT

operate

fi

replace with glass removed, cracked,

broken or scratched.

•

Replace as a complete assembly.

Removing Fixed Glass Assembly

• Pull the four glass assembly latches out of the groove on

the glass frame. Remove glass door from the appliance
(see Figure 14.4).

Replacing Fixed Glass Assembly

• Replace the glass door on the appliance. Pull out and

latch the four glass assembly latches into the groove on
the glass frame.

Air Shutter Settings

I. Install Trim and/or Surround

• Install optional trim kits and/or surrounds using the

instructions included with the accessory.

• Use non-combustible materials to cover the gap between

the sheet rock and the appliance (when applicable to the
model).

GLASS

ASSEMBLY

LATCHES

(BOTH BOTTOM

AND TOP)

AIR SHUTTER
WING NUT

J. Air Shutter Setting

Air shutter settings should be adjusted by a quali

fi

ed ser-

vice technician at the time of installation. The air shutter is
set at the factory for minimum vertical vent run. Adjust air
shutter for longer vertical runs. See Figure 14.5.
•  Loosen the wing nut.
•  Move the air handle to the left to open the air shutter.
•  Move the air handle to the right to close the air shutter.
•  Tighten the wing nut.

NOTICE:

If sooting occurs, provide more air by opening

the air shutter.

NG

LP

6000

1/4 in.

3/4 in.

8000

1/4 in.

3/4 in.

«
...
63
64
65
66
67
...
»

Summary of Contents for 6000C-IPI






















































































Reviews:

No comments

Related manuals for 6000C-IPI

Brand: Magiglo Pages: 52

COLLETTE L-FT629PST-A

Brand: HAMPTON BAY Pages: 6

Brand: HAMPTON BAY Pages: 48

Brand: HAMPTON BAY Pages: 8

Brand: Mendota Pages: 80

Brand: Xaralyn Pages: 11

Brand: ModaFlame Pages: 4

Brand: Napoleon Pages: 42

FIREBLAZE 37 315 14

Brand: Glow-worm Pages: 24

Brand: pleasant hearth Pages: 18

Brand: Cal Flame Pages: 32

Brand: Archgard Pages: 42

Brand: Majestic Pages: 44

Brand: Quadra-Fire Pages: 28

Apollo Crea7ion.E Series

Brand: GlammFire Pages: 16

Brand: Kennedy Pages: 24

Brand: Nibe Pages: 20

Brand: Charmglow Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands