background image

1

- Do not store or  use gasoline or other flam-

mable vapors and liquids in the vicinity of this

or any other appliance.

-

What to do if you smell gas

• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call

the fire department.

- Installation and service must be performed by a

qualified installer, service agency, or the gas

supplier.

Model:

SL-350TV

Installers Guide

WARNING:  IMPROPER  INSTALLA-

TION, ADJUSTMENT, ALTERATION,

SERVICE  OR  MAINTENANCE  CAN

CAUSE INJURY OR PROPERTY DAM-

AGE. REFER TO THIS MANUAL. FOR

ASSISTANCE OR ADDITIONAL INFOR-

MATION  CONSULT A  QUALIFIED  IN-

STALLER, SERVICE AGENCY, OR THE

GAS SUPPLIER.

Underwriters

Laboratories Listed

541-985C  4/00

READ THIS MANUAL BEFORE INSTALLING OR

OPERATING THIS APPLIANCE. THIS 

INSTALLERS

GUIDE 

MUST BE LEFT WITH APPLIANCE FOR

FUTURE REFERENCE.

Please  contact  your  Heat-N-Glo  dealer  for  any

questions  or  concerns.  For  the  number  of  your

nearest Heat-N-Glo dealer, please call 952-985-6000.

Printed in U.S.A.   Copyright 2000,
Heat-N-Glo, a division of Hearth Technologies Inc.

20802 Kensington Boulevard, Lakeville, MN 55044

WARNING: IF THE INFORMATION

IN THESE INSTRUCTIONS IS NOT

FOLLOWED EXACTLY, A FIRE OR

EXPLOSION MAY RESULT CAUS-

ING PROPERTY DAMAGE, PER-

SONAL INJURY, OR DEATH.

This  product  is  covered  by  one  or  more  of  the  following  patents:  (United  States)  4,112,913;  4,408,594;  4,422,426;  4,424,792;  4,520,791;  4,793,322;

4,852,548;  4,875,464;  5,000,162;  5,016,609;  5,076,254  5,191,877;  5,218,953;  5,328,356;  5,429,495;  5,452,708;  5,542,407;  5,613,487;  (Australia)

543790;  586383;  (Canada)  1,123,296;  1,297,746;  2,195,264;  (Mexico)  97-0457;  (New  Zealand)  200265;  or  other  U.S.  and  foreign  patents  pending.

Summary of Contents for SL-350TV

















Reviews: