Heat Line Capriz 2 24c Operating Instructions Manual Download Page 11

Operation 4

0020206382_02 Capriz 2 Operating instructions

11

If the filling pressure is too low, add
more water to the heating installa-
tion.

Note

If the heating flow temperature
is shown in the display, press
and hold the

and

buttons

at the same time for longer than
five seconds, or temporarily
deactivate heating mode in
order to display the pressure.

2. Fill the heating installation. (

Page 11)

4.4 Filling the heating installation

Caution.
Risk of material damage due

to heating water that is ex-

tremely calciferous or corros-

ive or contaminated by chem-

icals.

Unsuitable tap water damages

the seals and diaphragms,

blocks components in the

product and heating installation

through which the water flows

and causes noise.

Only fill the heating install-

ation with suitable heating

water.

In case of doubt, ask a com-

petent person for details.

Note

The competent person is respons-
ible for filling the heating installa-
tion the first time, any subsequent
top-ups and the water quality.
The operator alone is respons-
ible for topping up the water in the
heating installation.

1. Open all radiator valves (thermostatic

radiator valves) of the heating installa-
tion.

2. Slowly open the filling cock, as shown

to you by the competent person.

3. Fill with water until the required filling

pressure is reached.

4. Check the filling pressure in the

display.

5. Close the filling cock after filling.

4.5 Selecting the operating mode

Note

The unit is always activated with
the preselected operating mode.

Press

repeatedly until the display

shows the required operating mode.

Symbol

Operating mode

+

H hot water

Heating only

Hot water only

No requirement

4.6 Setting the hot water

temperature

Conditions

: The temperature is controlled by the

boiler

Set the hot water temperature on the
boiler (

Page 12).

Conditions

: The temperature is controlled by the

controller

Set the hot water temperature on the
controller.

Note

If you press the

or

button,

the display shows the

sym-

bol.

Summary of Contents for Capriz 2 24c





















Reviews: