Heat Controller Comfort-Aire PS-101A Installation, Operation & Maintenance Manual Download Page 15

15

Heat Controller, Inc. 

PS-81, 101, 121A

 

Installation, Operation & Maintenance

TROUBLESHOOTING  TIPS

TROUBLESHOOTING

1. Unit does not
    Start when
    Pressing on/off
    Button

PROBLEM

POSSIBLE CAUSES

SUGGESTED REMEDIES

Reset the temperature.

Make sure all the windows and
doors are closed.

Remove the heat sources if possible.

Connect the duct and make
sure it can function properly.

Decrease the set temperature.

Clean the air filter.

-   Room temperature is lower than
    the set temperature.(Cooling mode)

-   The windows or doors in the room
    are not closed.

-   There are heat sources inside the 
    room.

-   Exhaust air duct is not connected or
    blocked.

-   Temperature setting is too high.

-   Air filter is blocked by dust.

2. Not cool enough

Place the unit on a flat, level
ground if possible.

It is normal.

-   The ground is not level or not flat 
    enough.

-   The sound comes from the flowing
    of the refrigerant inside the 
    air-conditioner.

4. Noisy or vibration

5. Gurgling  sound

Switch on again after the unit 

has cool down.

-  The automatic over heat 

   protection function. When the 

   temperature at the air outlet 

O

O

   exceed 70 C/158 F,th e  de vice 

      will st op.

6. Power shut off at
    Heating mode

-   P1 appears in the display window

Drain  the water in the bottom tray.

Summary of Contents for Comfort-Aire PS-101A

















Reviews: