background image

WARNING

DO NOT DISCARD THIS MANUAL

CAUTION

•  Important operating and 

maintenance instructions 
included.

•  Leave this manual with 

party responsible for use 
and operation.

•  Read, understand and 

follow these instructions 
for safe installation and 
operation.

•  Do not store or use gasoline or other fl am-

mable vapors and liquids in the vicinity of this 
or any other appliance.

•  What to do if you smell gas   

-  D o   n o t   t r y   t o   l i g h t   a n y   a p p l i a n c e . 

                                                                       

Do not touch any electrical switch. Do not 
use any phone in your building.

-  Immediately call your gas supplier from a 

neighbor’s phone. Follow the gas supplier’s 
instructions.

-  If you cannot reach your gas supplier, call 

the fi re department.

•  Installation and service must be performed 

by a qualifi ed installer, service agency, or the 
gas supplier.

     WARNING:  If the information in these 
instructions is not followed exactly, a 

fi

 re 

or explosion may result causing property 
damage, personal injury, or death.

 

This appliance may be installed as an OEM installation in 
manufactured home (USA only) or mobile home and must be 
installed in accordance with the manufacturer's instructions and 
the manufactured home construction and safety standard,

 Title 

24 CFR, Part 3280 or Standard for Installation in Mobile Homes, 
CAN/CSA Z240MH.

This appliance is only for use with the type(s) of gas indicated on 
the rating plate.

Installation and service of this appliance should be 
performed by qualifi ed personnel. Hearth & Home 
Technologies suggests NFI certifi ed or factory-trained 
professionals, or technicians supervised by an NFI 
certifi ed professional.

DO NO

T

DISCARD

TIARA PETITE B

DIRECT VENT ROOM HEATER 

Owner’s Manual

Installation and Operation

TIARAP-BK
TIARAP-BR

TIARAP-CES

Model: 

O-T 

O-T L

Tested and 

Listed by

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

C

US

In the Commonwealth of Massachusetts:
•  installation must be performed by a licensed plumber or 

gas fi tter.

See Table of Contents for additional Commonwealth of 
Massachusetts requirements.

HOT SURFACES!

Glass and other surfaces are 
hot during operation AND cool 
down.

Hot glass will cause burns.

•  Do not touch glass until it is cooled 
•   NEVER allow children to touch glass
•  Keep children away
•  CAREFULLY SUPERVISE children in the same room as  

appliance

•   Alert children and adults to hazards of high temperatures

High temperatures may ignite clothing or other 

fl

 ammable materials.

•  Keep clothing, furniture, draperies and other combustibles 

away. 

Heat & Glo  •  Tiara Petite B  •  7026-101 Rev. N  •  10/11

Summary of Contents for TIARA PETITE B TIARAP-BK























































Reviews: