background image

Heat & Glo  •  ST-36TVB-IPI  •  2134-900 Rev. i  •  3/13

1

Model:
ST-36TVB-IPI

DO NOT

 store or use gasoline or other fl am-

mable vapors and liquids in the vicinity of this 
or any other appliance.

•  What to do if you smell gas 

-

DO NOT

 try to light any appliance.

-

DO NOT

 touch any electrical switch. 

DO

NOT

 use any phone in your building.

-  Immediately call your gas supplier from a 

neighbor’s phone. Follow the gas suppli-
er’s instructions.

-  If you cannot reach your gas supplier, call 

the fi re department.

•  Installation and service must be performed 

by a qualifi ed installer, service agency, or the 
gas supplier.

WARNING: If the information in these 

instructions is not followed exactly, a fi re 
or explosion may result causing property 
damage, personal injury, or death.

Owner’s Manual

Installation and Operation

DO NOT DISCARD THIS MANUAL

NOTICE

Installation and service of this appliance should be 
performed by qualifi ed personnel. Hearth & Home 
Technologies suggests NFI certifi ed or factory trained
professionals, or technicians supervised by an NFI 
certifi ed professional.

•  Leave this manual with 

party responsible for use 
and operation.

DO NO

T

DISCARD

WARNING

• Important operating 

a n d   m a i n t e n a n c e 
instructions included.

•  Read, understand and follow 

these instructions for safe 
installation and operation.

In the Commonwealth of Massachusetts installation must be 
performed by a licensed plumber or gas fi tter.

A CO detector shall be installed in the room where the appliance 
is installed.

This appliance has been supplied with an integral barrier 
to prevent direct contact with the fi xed glass panel. DO 
NOT operate the appliance with the barrier removed. 

Contact your dealer or Hearth & Home Technologies if the 
barrier is not present or help is needed to properly install one.

HOT SURFACES

!

Glass and other surfaces are hot during 
operation AND cool down.

Hot glass will cause burns.

DO NOT

 touch glass until it is cooled

•  NEVER allow children to touch glass
•  Keep children away

•  CAREFULLY SUPERVISE children in same room as 

fi replace.

•  Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other fl ammable 
materials.

•  Keep clothing, furniture, draperies and other fl ammable 

materials away.

Para obtener un ejemplar en Español de este
Manual del propietario, visite www.heatnglo.com.

Pour demander un exemplaire en français de ce Manuel 

du propriétaire, visitez www.heatnglo.com.

Summary of Contents for ST-36TVB-IPI












































Reviews: