Heat & Glo SLR-X-AU Installation Manual Download Page 52

Page: 52 / 57

Heat & Glo • SLR-X-AU Installation Manual • 2493-980 Rev. B • 12/17

H. Install Decorative Front

WARNING! Risk of Fire!

Install ONLY decorative fronts

approved by Hearth & Home Technologies. Unapproved

decorative fronts could cause fireplace to overheat.

This fireplace has been supplied with an integral barrier

to prevent direct contact with the fixed glass panel. DO

NOT operate the fireplace with the barrier removed.

Contact your dealer or Hearth & Home Technologies if

the barrier is not present or help is needed to properly

install one.
For more information refer to the instructions supplied with

your decorative front.

G. Install Fan Brackets

NOTICE:

These brackets are designed to improve the

effeciency of the fan performance by directing discharge

air through the CFT decorative front more effiecently.

1. Locate the fan brackets that are enclosed in the

manual bag assembly. Separate into left and right

brackets by bending the bracket at the perforation

until it breaks and the pieces are separated. See

Figure 11.2.
2. Install the right bracket by installing it over the glass

frame as shown in Figure 11.3.

3. Repeat Step 6 for left bracket. Notice the “L” indicator

on the left fan bracket.

“L” INDICATOR

BEND BRACKET AT PERFORATION

LEFT BRACKET

RIGHT BRACKET

Figure 11.2 Separate Fan Bracket into Left and Right Brackets

Figure 11.3 Separate Fan Bracket into Left and Right Brackets

Summary of Contents for SLR-X-AU


























































Search results

Summary of Contents for SLR-X-AU

Reviews:

Brands by name

Popular brands

Heat & Glo SLR-X-AU, Installation Manual

Search results

Summary of Contents for SLR-X-AU

Reviews:

Brands by name

Popular brands