Heat & Glo SLR-X-AU Installation Manual Download Page 48

Page: 48 / 57

Heat & Glo • SLR-X-AU Installation Manual • 2493-980 Rev. B • 12/17

D. Decorative Front Finishing

WARNING! Risk of Fire!

A decorative front is required

for this model. DO NOT operate this appliance without a

decorative front in place.

Only decorative fronts certified for use with this appliance

model may be used. Contact your dealer for a list of deco

rative fronts that may be used.

Overlap Fit
(0 - 1 in. max. (0 - 25 mm max.)

Thick Finishing Material)

Figure 10.8 Overlap Fit Method (CFT Decorative Front)

FACTORY-INSTALLED

NON-COMBUSTIBLE BOARD

NON-COMBUSTIBLE

FINISHING MATERIAL 0 - 1

IN (0 - 25 mm). THICK

NON-COMBUSTIBLE

FINISHING MATERIAL 0 -

1 IN. (0 - 25 mm) THICK

CFT

DECORATIVE

FRONT SHOWN

DRYWALL OR EQUIVALENT

(10 mm)

Non-Combustible Finish Materials

0 - 1 in. (0 - 25 mm) Thick

Overlap Fit Method

The CFT is designed to overlap finish materials 0 in.

to 1

in (0 - 25 mm) thick. See Figure 10.8.

NOTICE:

This one inch maximum not only includes the

decorative finish materials (marble, tile, slate, etc) but

also the mortar or adhesive used to attach the decorative

finish material

The non-combustible finish material can be installed up to

the fireplace opening.

FRONT FACE OF FIREPLACE

DECORATIVE FRONT

1 IN. (25 mm) MAX.

FINISHING MATERIAL

(TOP EDGE)

Figure 10.7 Overlap Fit Decorative Front

(CFT Decorative Front)

Finishing materials 1 in. (25 mm) maximum thick.

Stop finishing material flush with opening.

Figure 10.9 CFT Front Installation With Outer Door Trim

OUTER DOOR TRIM

INNER DOOR

ASSEMBLY

TOP VANITY PANEL

(NOT SHOWN)

TABS (4)

FACE OF NON-COMBUSTIBLE BOARD

Summary of Contents for SLR-X-AU


























































Search results

Summary of Contents for SLR-X-AU

Reviews:

Brands by name

Popular brands

Heat & Glo SLR-X-AU, Installation Manual

Search results

Summary of Contents for SLR-X-AU

Reviews:

Brands by name

Popular brands