3
15.
Insert the leg of the top pivot bracket up into the hole in
the door track. Line up the top pivot bracket with hole in
the corner brace on top of the door and attach with the
slotted hinge screw and steel washer (both doors).
16.
Align doors by readjusting the pivot brackets and steel
washers and sliding the doors in or out.
17.
Insert the ball stud into the hole in the ball stud plate.
Slide into the door as shown in Figure 6.
OPERATING PRECAUTIONS AND
INSTRUCTIONS
The glass doors and the fireplace flue damper must both be
in the fully open position before starting your fire.
Follow the procedure for building and starting a fire as de-
tailed in your fireplace homeowners manual. You may close
the doors AFTER the fire is well started. THE FIRST FEW
FIRES MUST BE SMALL TO ALLOW THE PROPER TEM-
PERING OF THE GLASS AND TO PREVENT GLASS
BREAKAGE.
Do not, however, close the doors on an excessively hot fire.
The glass must be allowed to warm slowly. Keep the fire
well back from the doors and never let flames contact the
glass.
If the fire gets too large at any time, open both sets of glass
doors. This will quickly reduce the heat in the firebox. Push
the logs or other fuel to the center of the firebox and rear-
range into single layer. Let the fire burn to a smaller size
before closing the glass doors again.
WARNING: FIREPLACES EQUIPPED WITH DOORS
SHOULD BE OPERATED ONLY WITH DOORS FULLY
OPEN OR DOORS FULLY CLOSED. IF DOORS ARE LEFT
PARTLY OPEN, GAS AND FLAME MAY BE DRAWN OUT
OF THE FIREPLACE OPENING, CREATING RISKS OF
BOTH FIRE AND SMOKE. MAKE SURE THE FIREPLACE
SCREEN IS CLOSED WHEN THE DOORS ARE OPEN.
The following check list summarizes the key steps discussed
under OPERATING INSTRUCTIONS:
1.
Open doors and fireplace damper.
2.
Build fire as described in fireplace manual.
3.
Close doors after the fire is started IF fire is normal
size.
4.
If fire gets too large, open doors and reduce size of fire.
5.
Keep damper open until fire is completely out and all
smoking has stopped.
For maximum benefit and efficient usage, refer to operating
instructions in owner's manual.
Figure 6
18.
Attach the ball stud receiver brackets to the bottom door
track. Use the 4 1/4" screws as shown in Figure 7.
Figure 7
19.
Line up the ball studs and receiver brackets by sliding
the receiver brackets up and down, and the ball studs
left and right. Once these parts are aligned, tighten the
screws on the receiver brackets and turn the ball stud
1/4 turn past hand tight. DO NOT OVER TIGHTEN THE
BALL STUD.
20.
If the ball studs and receiver brackets are not holding
the doors closed, you may need to compress the gas-
ket material on the back of the door by pressing it down
with your fingers.
NOTE
: The ball stud may need to be adjusted after the first
couple of fires. Periodically check the alignment of the ball
stud with the ball stud receiver bracket and adjust if neces-
sary.
BALL STUD
BALL STUD
PLATE
BALL STUD
RECEIVER BRACKETS
REPLACEMENT PARTS
KITS
GD415ATBPB
GD485ATPB
Side Filler
690-105
690-105
Front Filler
690-106
691-106
Top/Bottom Tracks
690-108
691-108
Left Door
690-390A
691-390A
Right Door
690-391A
691-391A
Hardware Kit
Includes:
Hinge: Bottom Left & Right
Hinge: Top Left & Right
Ball Stude & Plate
Ball Stud Receiver Bracket
Handles & 3/4" Screws for Handles
Slotted Hinge Screws
Washers
1/2" Sheetmetal Screws
1/4" Screws for Ball Stud
Receiver Bracket
690-100A
690-100A
REPLACEMENT PARTS
