23
Use & Care Guide
System Specification and Performance Data Sheet
Refrigerator Water Filter Cartridge Model UKF8001AXX
Specifications
Service Flow Rate (Maximum) .....................................
0.78 GPM (2 9 L/min)
Rated Service Life UKF8001AXX-750 (Maximum)
....... 750 gallons/2839 liters
Maximum Operating Temperature ................................ 100° F / 38° C
Minimum Pressure Requirement .................................. 35 psi /241 kPA
Minimum Operating Temperature ................................. 33° F/1° C
Maximum Operating Pressure ...................................... 100 psi / 689 kPA
PentaPure Inc.
1000 Apollo Road
Eagan, Minnesota 55121-2240
651 450 4913
EPA EST #35917-MN-1
100834/B
* Tested using a flow rate of 0.78 gpm; pressure of 60 psig; pH of
7.5 + 0.5; temp. of 68° + 5° F (20° + 3° C)
** Measurement in Particles /ml. Particles used were 0.5 - 1
microns
*** NTU - Nephelometric Turbidity Units
General Use Conditions
Read this Performance Data Sheet and compare
the capabilities of this unit with your actual water
treatment needs.
DO NOT use this product where water is mi-
crobiologically unsafe or of unknown quality
without adequate disinfection before or after
the system. System certified for cyst reduction
may be used on disinfected water that may
contain filterable cysts.
USE ONLY WITH COLD WATER SUPPLY.
CHECK FOR COMPLIANCE WITH THE STATE
AND LOCAL LAWS AND REGULATIONS.
Tested and certified by NSF International against ANSI/NSF Standards
42 & 53 in models UKF8001AXX-750 for the reduction of:
Standard No. 42: Aesthetic
Effects
Taste and Odor Reduction
Chlorine Taste & Odor
Mechanical Filtration Unit
Particulate Reduction Class 1
Standard No. 53: Health Effects
Chemical Reduction Unit
Lead, Atrazine, Lindane, Mercury &
Toxaphene Reduction
Mechanical Filtration Unit
Cyst, Turbidity and Asbestos reduction
The PuriClean® II retractable water filtration system uses a
UKF8001AXX replacement cartridge. Timely replacement of
filter cartridge is essential for performance satisfaction from
this filtration system.
Please refer to the applicable section of your Use & Care
Guide for general operation, maintenance requirements and
troubleshooting.
This system has been tested according to ANSI/NSF 42 and
53 for reduction of the substance listed above. The concentra-
tion of the indicated substances in water entering the system
was reduced to a concentration less than or equal to the
permissible limit for water leaving the system, as specified in
ANSI/NSF 42 and 53.
Average
Maximum
Average
Minimum
Chlorine
—
2.0 mg/L ± 10%
1.88 mg / L
<0.05136364 mg /L
0.06 mg /L
>97.26%
96.84%
50%
—
—
—
—
—
—
—
—
O
&
T
Particulate**
—
at least 10,000 particles / ml
5,700,000 # /ml 30,583 # /ml 69,000 #/ml
99.52%
98.94%
85%
Average
Maximum
Average
Minimum
Turbidity
1 NTU**
11 ± 1 NTU***
10.7 NTU
0.31 NTU
.049 NTU
97.09%
95.20%
0.5 NTU
Cysts
99.5% Reduction
Minimum 50,000/L
166,500 #/L
<1 #/L
<1 #/L
>99.99%
>99.99%
>99.95%
Asbestos
99% Reduction
107 108 fibers/L; fibers >10 micrometers in length
155 MF/L
<1 MF/L
<1 MF/L
>99.99%
>99.99%
99%
Lead at pH 6.5
0.015 mg/L
0.15 mg/L + 10%
0.153 mg/L
< .001 mg/L
< .001 mg/L
>99.35%
>99.29%
0.10 mg/L
Lead at pH 8.5
0.015 mg/L
0.15 mg/L + 10%
0.150 mg/L
< .001 mg/L
< .001 mg/L
>99.33%
>99.29%
0.10 mg/L
Mercury at pH 6.5
0.002 mg/L
.006 mg/L ± 10%
0.006 mg/L
0.0003 mg/L 0.0005 mg/L
95.70%
90.91%
0.002 mg/L
Mercury at pH 8.5
0.002 mg/L
.006 mg/L ± 10%
0.006 mg/L
0.0008 mg/L 0.0015 mg/L
86.22%
75.93%
0.002 mg/L
Atrazine
0.003 mg/L
0.009 mg/L + 10%
0.009 mg/L
< 0.002 mg/L 0.002 mg/L
76.99%
75.31%
0.003 mg/L
Lindane
0.0002 mg/L
0.002 mg/L + 10%
0.002 mg/L
0.000 mg/L < 0.0001 mg/L
98.72%
96.50%
0.0002 mg/L
Toxaphene
0.003 mg/L
0.015 ± 10%
0.015 mg/L
<0.001 mg/L <0.001 mg/L
92.97%
91.67%
0.003 mg/L
Standard No. 42: Aesthetic Effects
Influent Challenge Concentration
Min. Required
Reduction
Parameter
Min. Required
Reduction
USEPA MCL
USEPA MCL
Standard No. 53: Health Effects
% Reduction
Effluent
Influent
Average
% Reduction
Effluent
n
o
it
a
rt
n
e
c
n
o
C
e
g
n
el
la
h
C
t
n
e
u
lf
n
I
r
e
t
e
m
a
r
a
P
Influent
Average