HearthRite HR15ML-1 Owner'S Operation And Installation Manual Download Page 11

Page: 11 / 28

Figure 17 - Control Knob in The
OFF Position

Figure 18 - Pilot

LIGHTING

INSTRUCTIONS

1 .    S TO P !     R e a d       t h e     s a f e t y
          information    on    the    side  of
       heater.
2.    Check    that    gas    supply    to
       heater  is  on.
3.    Push    in    gas    control    knob
        slightly  and  turn clockwise

the OFF position.

NOTE:

Knob cannot be turned from

“PILOT”  to  “OFF”  unless knob  is
pushed  in  slightly.  Do  not  force.
4.   Wait five (5) minutes  to  clear
        out  any  air. Then   smell  for  gas,
      including near the floor. If  you
        smell  gas,STOP!  Follow   “B”  in
       the  safety  information  on  the
        side of  the heater.  If  you  do not
        smell gas,  go  to  the  next  step.
5.    Push    in   gas   control   slightly

and turn counterclockwise

to “PILOT/IGN” and depress

for five(5) seconds

NOTE:

The first time that the

heater   is  operated  after connecting
the   gas  supply ,  the    control  knob
should  be  depressed for  about  thirty
(30) seconds.  This will   allow  air   to
bleed from  the  gas  system.

6.    With  control  knob  pressed  in,
      push  down  and   release   the
          ignitor  button.  This    will    light
        pilot.   If  needed,   keep   pressing
        ignitor  button  until  pilot  lights.
7.   Keep  control  knob  depressed
        for    ten  (10)    seconds    after
      lighting  pilot. If  pilot  goes  out,
       repeat  steps 5, 6  and  7.
8.   To  select  the  desired  heating
       level,  partially   press  down  the
       control  knob  slightly  and  rotate
      counterclockwise

. Release the

        downward  pressure  on  the  knob
       while  continuing to  turn  until  the
       knob  locks at   the desired  setting
      p o s i t i o n .     D o   n o t     o p e r a t e
       between  locked  positions.

Shutting Off Heater

1. Turn control knob clockwise

to the OFF position.

2.    Turn  off  all   electric   power   to
       the  appliance  if  service  is  to be
       performed.

Shutting Off Burner Only ( pilot
stays lit)

Turn control knob clockwise
to the PILOT/IGN position.

MANUAL LIGHTING

PROCEDURE

1.    Remove lower  front  panel (see
       Figure 7 page 7).
2.    Follow  steps 1  through  5  under

Lighting Instructions.

3.     With   control   knob   pressed  in,
        strike    match.    Hold   match    to
        pilot until pilot lights.
4.   Keep  control  knob  pressed  in
          for  30    seconds    after  lighting
      pilot.  After  30  seconds, release
       control    knob.  Follow   step   8
        under

Lighting Instructions.

5. Replace lower front panel.

TO SELECT

HEATING LEVEL

CAUTION:

Do not try to

adjust heating levels by using
the equipment shutoff valve.

WARNING:

When running

heater,set  control knob  at LOW,
M E D I U M ,   o r     H I G H     l o c k e d
positions. Never  set  control knob
between    locked  positions.  Poor
combustion and  higher  levels  of
carbon monoxide  may  result.

Figure 19 - Burner Patterns

Slightly press in control knob and

turn counterclockwise

to the

LOW,MEDIUM, or HIGH position

(see Figure 19).

IMPORTANT

: Release downward

pressure while turning control knob.

Control knob will lock at the desired

position.

TO TURN OFF