4
MATCHING SECURITY CODES
It may be necessary to program the remote receiver to
the security code of the transmitter upon initial use, if
batteries are replaced, or if a replacement transmitter
is purchased from your dealer. To program the remote
receiver:
1. Set the slide button on the receiver to the REMOTE
position.
2. Push the LEARN button (one beep will be heard) on
the top of the remote receiver.
3. Then press the ON/OFF button on the transmitter.
Several beeps indicate the transmitter’s code has
been programmed into the receiver. When an exist-
ing receiver is matched to a new transmitter, the
new security code will overwrite the old one.
NOTE:
When the LEARN button is depressed, “beeping”
sounds should be heard. If no “beeping” is heard
check to see that the receiver has 110-120VAC
power to it.
If you are unsuccessful in matching the security code
on the first attempt, wait 1-2 minutes before trying again.
NOTE:
If the transmitter is activated from a very cold
condition it may be necessary to allow the transmitter
to stabilize to room temperature (could take up to 15
minutes) before accurate room temperatures are dis-
played on the screen.
NOTE:
LCD screen is equipped with a “backlite” for
easier viewing of LCD screen. Backlite illuminates when
a function button is depressed. After 5 seconds elapses,
LCD screen will return to its normal state.
Setting
0
F/
0
C Scale
The factory setting for temperature is degrees Fahrenheit
(
0
F). To change this setting to degrees Centigrade (
0
C):
1. Remove the battery cover on the back of the trans-
mitter and locate the “setting button” at the top cen-
ter of battery compartment (see Figure 5).
2. Push setting button and
0
F will begin flashing on the
LCD screen (see Figure 4, Location #2).
3. Push the ON/OFF button on the transmitter to
change
0
F to
0
C.
4. Push “setting button” on transmitter and Centigrade
(
0
C) degree readings will display on LCD screen.
5. Repeat this process to change back to Fahrenheit
(
0
F) reading.
NOTE:
LCD screen will return to nor-
mal state if setting button is not pushed within 15
seconds.
Figure 5. Setting Button/Child Proof Lockout
Room Temperature
The room temperature is displayed in either
0
F or
0
C.
The transmitter should be kept away from direct sources
of heat such as fireplaces, incandescent lighting and
direct sunlight. Leaving the transmitter in direct sun-
light, for example, will cause it to read the room tem-
perature higher than it actually is.
Fireplace Control - ON/OFF
The flame icon will display on the LCD screen (see
Figure 4 Location #3) when the ON/OFF button has
been pushed and the fireplace is ON. The flame icon
will disappear when the ON/OFF button is pushed again
and the fireplace is off.
Low/Battery Indicator
An “X” outlined by a battery (see Figure 4, Location #4)
on the left side of the LCD screen will appear when
battery power has dropped significantly. At this time,
approximately two weeks of battery power remains.
Child Proof Lockout (CP)
The transmitter contains a “Child Proof” lockout feature
that prevents unauthorized use of the remote control.
To access the “Child Proof” activation button, remove
cover on BACK of transmitter. To activate LOCKOUT:
1. Press and hold in the “setting button” for 5 sec-
onds. The letters CP will display on the LCD screen
(see Figure 7). This prevents the activation of fire-
place. When ON/OFF button is pressed, the let-
ters CP will display on the LCD screen.
To deactivate LOCKOUT:
1. Press and hold in the “setting button” for 5 sec-
onds. The LCD will display CP until 5 seconds have
elapsed, and then the LCD screen will return to its
normal state.
f i r e - p a r t s . c o m
