Hearth & Home B41L-AU Owner'S Manual Download Page 26

Page: 26 / 28

Hearth & Home Technologies • B41L-AU Owner Manual • 2570-981 Rev. B • 5/20

Service Parts

B41L-AU

Beginning Manufacturing Date: May 2020

Ending Manufacturing Date: Active

IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor.

Hearth and Home Technologies does

not sell directly to consumers.

Provide model number and serial number when requesting service parts from your dealer or distributor.

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

15.1

Pilot Shield

2491-123

15.2

Pilot Assembly NG

2106-169

Pilot Assembly Propane

2106-170

15.3

Grommet

SRV2118-420

15.4

Burner Support, Left and Right

1 Set

2491-169

15.5

Gasket

2025-407

15.6

Bulkhead W/Flex Tube

4021-428

15.7

Valve Bracket

2491-153

15.8

Flex Ball Valve Assembly, 12”

SRV302-320

15.9

Valve NG

2166-302

Valve Propane

2166-303

15.10

Male Connector

Pkg of 5

303-315/5

15.11

Transformer, 6 Volt Wall

SRV2326-131

15.12

Jumper Wire

SRV2187-198

15.13

Module, Grey

2166-306

15.14

Power Cord Assembly

2222-037

15.15

Thermostat Wire

SRV2118-170

15.16

Battery Pack

SRV2166-323

15.17

Wire Harness

2166-304

Orifice NG (#44C)

582-844

Orifice Propane (55C)

582-855

Additional service part numbers appear on following page.

#15 Valve Assembly

15.1

15.2

15.3

15.4

15.5

15.6

15.7

15.8

15.9

15.10

15.11

15.12

15.13

15.16

15.17

15.15

15.14

Summary of Contents for B41L-AU





























Search results

Summary of Contents for B41L-AU

Reviews:

Related manuals for B41L-AU

Brands by name

Popular brands

Hearth & Home B41L-AU, Owner'S Manual

Search results

Summary of Contents for B41L-AU

Reviews:

Related manuals for B41L-AU

Brands by name

Popular brands