background image

9

Quadra-fire  •  QV32B-A, QV36B-A  •  2014-900  Rev. F  •  9/06

1

Approvals and
Codes

NOTE: THESE MODELS ARE UL LISTED TO UL307B,
THE STANDARD FOR GAS-BURNING HEATING APPLI-
ANCES FOR MANUFACTURED HOMES AND RECRE-

ATIONAL VEHICLES.

Installation Codes

The fireplace installation must conform to local codes. Before
installing the fireplace, consult the local building code
agency to ensure that you are in compliance with all
applicable codes, including permits and inspections.

In the absence of local codes, the fireplace installation must
conform to the  National Fuel Gas Code ANSI Z223.1 (in
the United States) or the CAN/CGA-B149 Installation Codes
(in Canada). The appliance must be electrically grounded
in accordance with local codes or, in the absence of local
codes with the National Electric Code ANSI/NFPA No. 70
(in the United States), or to the  CSA C22.1 Canadian Electric
Code (in Canada).

These models may be installed in a bedroom or bed-sitting
room in the U.S.A. and Canada.

Appliance Certification

The Village Collection fireplace models discussed in this

Installers Guide

 have been tested to certification standards

and listed by the applicable laboratories.

Certification

MODELS:

  QV32B-A, QV36B-A

LABORATORY:   

 Underwriters Laboratories

TYPE:    

Vented Gas Fireplace Heater

STANDARD: 

   ANSI Z21.88•CSA2.33•UL307B

High Altitude Installations

U.L. Listed gas appliances are tested and approved without
requiring changes for elevations from 0 to 2,000 feet in the
U. S. A. and in Canada.

When installing this appliance at an elevation above 2,000
feet, it may be necessary to decrease the input rating by
changing the existing burner orifice to a smaller size. Input
rate should be reduced by 4% for each 1000 feet above a
2000 foot elevation in the U.S.A. or 10% for elevations
between 2000 and 4500 feet in Canada. If the heating value
of the gas has been reduced, these rules do not apply. To
identify the proper orifice size, check with the local gas
utility.

If installing this appliance at an elevation above 4,500 feet
(in Canada), check with local authorities.

Summary of Contents for QV32B-A












































Reviews: