background image

Page 1 of 54   

CLIENT # LC773211 

 

          THE AUSTIN 65L 
               38,000 BTU 

   

Natural Gas & Propane 

Installation and Operating Instructions 

 
 

MODEL:

 

AUSTIN-65G-NG-DELUXE, AUSTIN-65G-LP-

DELUXE 

 

 

 
 

 
 

                

 

 
 

 

 
 
 

WARNING 

IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR 

EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH. 

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or 

any other appliance. 

WHAT TO DO IF YOU SMELL GAS: 

 

Do not try to light any appliance 

 

Do not touch any electrical switch; do not use any phone in your building 

 

Immediately call your gas supplier from a neighbour’s phone. Follow gas supplier’s 
instructions 

 

If you cannot reach your gas supplier, call the fire department. 

Installation and service must be performed by a qualified installer, service agency or gas 
supplier. 

WARNING: Improper installation, adjustment, alteration, services or maintenance can cause 
injury or property damage. Refer to this manual. For assistance or additional information 
consult a qualified installer, service agency or the gas supplier. 

INSTALLER: Leave this manual with the appliance. 
 
CONSUMER: Retain this manual for future reference.

 

PLEASE READ THIS MANUAL BEFORE 

INSTALLING OR USING THIS APPLIANCE.  

SAVE THIS MANUAL FOR FUTURE 

REFERENCE. 

A BARRIER DESIGNED TO REDUCE THE RISK OF 
BURNS FROM THE HOT VIEWING GLASS IS 
PROVIDED WITH THIS APPLIANCE AND SHALL BE 
INSTALLED.

 

Summary of Contents for AUSTIN-65G-LP-DELUXE























































Reviews: