background image

27

Locate the Reed Switch (22) and the Magnet (18) on
the left side of the Pulley (17). Turn the Pulley until the
Magnet is aligned with the Reed Switch. 

Make sure

that the gap between the Magnet and the Reed
Switch is about 1/8”.

If necessary, move the Reed

Switch slightly using a slotted screwdriver. Next, reat-
tach the Motor Hood (not shown), making sure that the
3/4” Screws (not shown) are in the same holes from
which they were removed. Then, run the treadmill for a
few minutes to check for a correct speed reading.

PROBLEM: The walking belt slows when walked on

SOLUTION:

a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 12.

b. If the walking belt is overtightened, treadmill perfor-

mance may decrease and the walking belt may be-
come damaged. Remove the key and 

UNPLUG THE

POWER CORD

. Using the hex key, turn both rear

roller bolts counterclockwise, 1/4 of a turn. When the
walking belt is properly tightened, you should be able
to lift each edge of the walking belt 3 to 4 inches off
the walking platform. Be careful to keep the walking
belt centered. Then, plug in the power cord, insert the
key, and run the treadmill for a few minutes. Repeat
until the walking belt is properly tightened.

c. If the walking belt still slows when walked on, see the front cover of this manual.

PROBLEM: The walking belt is off-center or slips when walked on

SOLUTION:

a. If the walking belt is off-center, remove the key and

UNPLUG THE POWER CORD

.

If the walking belt

has shifted to the left,

use the hex key to turn the

left rear roller bolt clockwise 1/2 of a turn; 

if the walk-

ing belt has shifted to the right,

turn the left rear

roller bolt counterclockwise 1/2 of a turn. Be careful
not to overtighten the walking belt. Plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is centered.

b. If the walking belt slips when walked on, first remove

the key and 

UNPLUG THE POWER CORD

. Using

the hex key, turn both rear roller bolts clockwise, 1/4
of a turn. When the walking belt is correctly tightened,
you should be able to lift each edge of the walking
belt 3 to 4 inches off the walking platform. Be careful
to keep the walking belt centered. Then, plug in the
power cord, insert the key, and carefully walk on the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.

3”–4”

b

a

b

18

22

Top 

View

1/8”

17

Rear Roller Bolts

Summary of Contents for Outlook HRTL89406.0





































Reviews: