background image

7

SPECIFICATIONS

DIGITAL AUDIO/VIDEO I/O

2801 Transmitter

1x via HDMI connector – HDMI input

2811 Receiver

1x via HDMI connector – HDMI output

CAT 5E/6 CONNECTIONS I/O

2801 Transmitter

1x via RJ-45 – Cat 5e/6 output

2811 Receiver

1x via RJ-45 – Cat 5e/6 input

VIDEO PERFORMANCE

Minimum resolution: 

720p

Maximum resolution :

1080p (1920x1200, 1080p/60Hz)

TMDS clock speed *: 

225MHz

Data bit rate *: 

2.25Gbps

Maximum range : 

250 ft. (75m) direct connection

 

 

    1000 ft. (300m) via GbE switches

REGULATORY APPROVALS

Transmitter (2801) and Receiver (2811)

HDMI, HDCP, RoHS

Power Supply

UL, CUL, CE, PSE, GS, RoHS

AUDIO PERFORMANCE

Digital Audio

2-channel PCM audio only

MECHANICAL

Dimensions: H-W-D inches (mm)

1.25 x 6.35 x 4.5 (32x162x115mm)

ENVIRONMENTAL

Operating Temperature

0° to +50° C (+32° to +122° F)

Operating Humidity

10% to 90%, Non-condensing

Storage Temperature

-10° to +70° C (12° to +158° F)

Storage Humidity

10% to 90%, non-condensing

IR PASS THROUGH

IR signals can be passed from the 2811 Receiver location(s) back to the 2801 Transmitter location (single Transmitter 
systems only) to control the source equipment. The HD-IP system may not be compatible with all IR equipment.
Note: IR signals cannot be passed reliably when more than one 2801 Transmitter is used in a network.

With power disconnected from the 2811 Receiver, 
connect a standard IR receiver to the 2811’s 3.5mm 
IR port. Pin out is shown below.

With power disconnected from the 
2801 Transmitter, connect a stan-
dard IR emitter to the 2801’s IR 
3.5mm IR port. Pin out is shown.

1.

2

Tip = Signal

Ring = Ground

Sleeve = +12 Volts

Tip = Signal

Ring = Gnd

Sleeve = +5V

Tip = (+)

 

Sleeve = (–)

Tip = Signal

Ring = Ground

Sleeve = +12 Volts

 

IR EMITTER

 

 

(2801 CONNECTION)

IR RECEIVER

 

(2811 CONNECTION)

Summary of Contents for 2801











Reviews: