USE ONLY HAYWARD GENUINE REPLACEMENT
PARTS
1
GENERAL
1.
Proper fitting make-up is hand tight plus one to 1-
1/2 turns maximum.
Always use Teflon pipe tape
or Permatex No.2 for connections to provide a
good, "living" seal.
IMPORTANT: Do not over tighten pipe fittings.
2.
SERVICING VALVE:
If it becomes necessary to
service or gain access to the key or valve seat
gasket:
a.
Set handle in “Winterizing” position.
b.
Remove cover screws.
c.
Lift cover and key assembly out.
3.
RE-ASSEMBLY VALVE:
a.
Wipe debris from cover 0-ring.
b.
Set handle in a “Winterizing” position. Align
flat edge on cover with body. Press down to
seat assembly.
c.
Secure assembly to body with cover screws
and nuts. Tighten cover screws evenly and
alternately.
Do not over tighten.
FUNCTIONS OF VALVE POSITIONS
VALVE
SETTING
FLOW DIRECTION THROUGH VALVE
FILTER
(Sand Filter)
PUMP - TOP - THROUGH FILTER - BOTTOM - RETURN
(DE Filter)
PUMP - BOTTOM - THROUGH FILTER - TOP - RETURN
For normal filtration and vacuuming pool through filter.
BACKWASH
(Sand Filter)
PUMP - BOTTOM - THROUGH FILTER - TOP – WASTE
(DE Filter)
PUMP - BOTTOM - THROUGH FILTER - TOP - WASTE
For cleaning filter.
RINSE
PUMP - THROUGH FILTER in filter direction - WASTE
For initial start-up and clearing valve of debris after
backwashing.
WASTE
PUMP – THROUGH VALVE ONLY - WASTE
For vacuuming directly to waste, lowering pool level
and/or draining pool.
CLOSED
NO CIRCULATION PAST PUMP PORT
For shutting off all flow to filter and pool.
RECIRCULATE
PUMP – THROUGH VALVE - RETURN
For bypassing filter, but circulating pool water.
WINTERIZING:
Drain and winterize filter and pump per manufacturer's
instructions. To drain water from VariFlo® Multiport
valve—depress and rotate valve handle and place handle
pointer between any detente positions.
VariFlo
®
Multiport
2” Filter Control Valve
Owner’s Manual
Model: SP0715ALL
TURN OFF PUMP BEFORE CHANGING VALVE POSITION
CAUTION –Spring Hazard
– Release of Valve spring compression can cause personal injury. To avoid, only remove handle
pin if servicing key O-ring. Remove handle pin before slowly removing Cover screws in an alternate pattern.
WARNING
-
Read and follow all instructions
in this owner’s manual and on the equipment.
Failure to follow instructions can cause severe injury and/or death.
Hayward Pool Products
620 Division Street, Elizabeth, NJ 07207
Phone: (908) 355-7995
WWW.HAYWARD.COM
IS0715 REV B
REF
NO.
PART NUMBER
DESCRIPTION
NO.
REQ’D
-
SPX0710FL
Handle, Large
-
1
SPX0715F
Handle, Standard
1
2
SPX0710XZ7
Pin, for Handle
1
3
SPX0710Z16
Non-Metallic Bearing
1
SPX0715G
Valve Position Label
1
4
SPX0710Z1A
Cover screw set with nuts (Set of 6)
1
5
SPX0715Z1
Cover O-ring
1
6
SPX0603S
Spring
1
7
SPX0710Z62
Spring Washer Set (Set of 2)
1
8
SPX0735GA
O-ring & TFE Shaft seal set
1
9
SPX0710K
¼” Plastic Pipe Plug
1
10
SPX0715D
Valve Seat Gasket
1
11
SPX0715C
Key 1
SPX0715BA
Key, Cover & Handle Assembly
1
