background image

Control Unit Set-Up

Cleaner Set-Up

The TigerShark Control Unit can be installed and  
used in different locations:

1.  Sitting on a table or on the pool deck

2.  Positioned on the caddy cart control unit cradle

Connect the cleaner cable to the control unit and plug the 
control unit cord into a protected outlet.

To reduce the risk of electric shock, do NOT use an extension 
cord to connect unit to electric supply. 

INSTALL

To find the best location for your control unit, please  
consider the following:

•  The control unit should preferably be kept in a shady area 

and the cooling fan kept unobstructed.

•  Leaving the control unit on the pool deck is acceptable but 

precautions should be taken so it does not get damaged by 
regular traffic around the pool or by playing children or pets.

•  The cleaner control unit should be located at least  

3.5 m (11.5 ft.) from the closest edge to the pool.

•  To reduce the risk of electric shock, 

DO NOT USE AN 

EXTENSION CORD

 to connect unit to electric supply.

•  Based on your region of the world, the cleaner control unit 

must be connected only to a supply circuit protected by a 
ground-fault circuit-interrupter (GFCI) or a residual  
current device (RCD).

240 V

50 Hz 

GFCI

220/230 V

50 Hz

RCD

110/220 V

50Hz/60Hz

Summary of Contents for TigerShark Series












Reviews: