USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
7
3.6.
Electrical Specs
Use copper conductors only. For indoor & outdoor use.
PUMP MODEL
TOTAL HP
RATED HP
VOLTAGE
AMPS
SP2305X7
0.95
0.75
115 / 208-230
10.0 / 6.0-5.0
SP2305X7EE
0.95
0.75
115 / 208-230
9.2 / 4.7-4.6
SP2305X7EESP
0.95
0.75
115 / 208-230
9.2 / 4.7-4.6
SP2307X10
1.25
1.00
115 / 208-230
13.3 / 6.9-6.8
SP2307X102
1.25 / 0.20
1.00 / 0.16
230
6.1 / 2.1
SP2310X15
1.65
1.50
115 / 208-230
16.5 / 9.2-8.5
SP2310X152
1.65 / 0.27
1.50 / 0.25
230
7.7 / 2.8
SP2315X20
2.10
2.00
115 / 208-230
17.4 / 10.6-8.8
SP2315X202
2.20 / 0.36
2.00 / 0.33
230
10.0 / 3.0
3.7.
Voltage
Voltage at pump MUST NOT be more than 10% above or below nameplate rated voltage, or components may
overheat, causing overload tripping and reduced component life. If voltage is less than 90% or more than 110% of
rated voltage when pump is running at full load, consult the power company.
3.8.
Grounding and Bonding
1.
Install, ground, bond, and wire pump in accordance with local or national electrical code requirements.
2.
Permanently ground pump. Use green ground terminal provided under access plate; use size and type wire
required by code. Connect ground terminal to electrical service ground.
3.
Bond pump to pool structure. Bonding will connect all metal parts within and around the pool with a continuous
wire. Bonding reduces the risk of a current passing between bonded metal objects, which could potentially
cause electrical shock if grounded or shorted. Reference NEC codes for all wiring standards including, but not
limited to, grounding, bonding and general wiring procedures.
4.
Use a solid copper conductor, size 8 or larger. Run wire from external bonding lug to reinforcing rod or mesh.
Connect a No. 8 AWG (8.4 mm
2
) [No. 6 AWG (13.3 mm
2
) for Canada] solid copper bonding wire to the pressure
wire connector provided on the motor housing and to all metal parts of swimming pool, spa, or hot tub, and to
all electrical equipment, metal piping (except gas piping), and conduit within 5 ft. (1.5 m) of inside walls of
swimming pool, spa, or hot tub.
3.9.
Wiring
WARNING
– All electrical wiring MUST conform to local codes, regulations and the National Electric
Code (NEC).
Pump MUST be permanently connected to circuit. If other lights or appliances are also on the same circuit, be sure
to add their amp loads before calculating wire and circuit breaker sizes. Use the load circuit breaker as the Master
On-Off switch.
WARNING
Risk of dangerous or fatal electrical shock
. Be sure that power to the motor
circuit is off before working on wiring, wiring connections, or motor. Re-install the motor end cover and all
other wiring covers before turning on the power.
To Wire a Single Speed, Single Voltage Motor
1. Turn off power.
2. Remove the motor end cover.
3.
There are two terminals labeled L1 and L2. Attach the power leads to these terminals. Either wire may attach to
either terminal.
4.
Reinstall motor end cover.
WARNING
– If you do not use conduit when wiring motor,
be sure
to seal wire opening on end of motor
to prevent dirt, bugs, etc., from entering.
