4
Installation - all models
1.
Teach the unique ID code
: The base station attached to the control unit has a
unique ID code that ensures that your unit will not affect other systems in the
neighborhood, and likewise, their remote will not affect your system. To teach
the ID code to the wireless remote unit:
a.
On any other wired Pro Logic/Aqua Logic dis-
play/keypad unit, press the "Menu" button
(possibly multiple times) until "Settings Menu"
is displayed.
b.
Press "<" or ">" (again, possibly multiple times)
until "Teach Wireless" is displayed.
c.
Press the "+" button to start the teaching pro-
cess.
d.
Press and hold any button on the wireless re-
mote display/keypad for 4 seconds. At this
point, the LCD on the wireless remote display/
keypad will indicate "Teach Wireless Success-
ful" and the local display/keypad on the Pro
Logic/Aqua Logic control unit will also con-
firm "Teach Wireless Successful". If this pro-
cess is not successful, then refer to the Trouble-
shooting section of this manual for additional
information.
2.
Apply labels:
The Pro Logic and Aqua Logic series of controls allow each
output (e.g. AUX1) to be renamed to what is actually being controlled. The
wireless remote display/keypad comes with a sheet of name labels—simply peel
the appropriate label off the sheet and apply to the appropriate set of buttons on
the wireless remote display/keypad.
3.
Installation is complete:
You can now use the wireless remote display/keypad.
5. Display backlight turns off after a period of time:
Models running off wall power:
The display backlight should always illuminate
when you press any key on the unit. If it turns off after a period of time, you can
stop this by pressing the menu key (possibly multiple times) until "Settings
Menu" appears. Next press the "<" or ">" key (possibly multiple times) until
"Display Light" appears. At this point, pressing either "+" or "-" will allow you to
select either "Always On" or "On for 60 sec.". After you have selected the
desired operation, press the "Menu" button to lock in your setting. Note that this
selection applies to this wireless remote display/keypad only. Repeat the process
of each display/keypad in the system.
6. Display backlight always on
Models running off wall power:
The display backlight should always illuminate
when you press any key on the unit. If it remains on after 60 seconds have
elapsed since the last button push, you can stop this by pressing the menu key
(possibly multiple times) until "Settings Menu" appears. Next press the "<" or
">" key (possibly multiple times) until "Display Light" appears. At this point,
pressing either "+" or "-" will allow you select either "Always On" or "On for 60
sec.". After you have selected the desired operation, press the "Menu" button to
lock in your setting. Note that this selection applies to this display/keypad only.
Repeat the process for each display/keypad in the system.
7.
The last keypress
was not received
This is usually a temporary problem caused by interference from other equip-
ment that is using the same radio frequency. Try pressing the button again. If
this doesn’t work, go to the Settings Menu/Wireless Channel on any other Pro
Logic/Aqua Logic display/keypad and select another channel. Note that after
you change the channel you will have to "re-teach" every wireless remote de-
vice in the system.
8.
The base station
is not responding
If this is the first time you are using your remote, or if you have just installed a
new base station, run the "Teach Wireless" procedure from any other display/
keypad. Also,
the radio signal may be too weak—try pointing the remote in the
direction of the pool equipment or try moving closer to the pool equipment. If
that doesn’t work, then there may be other equipment that is using the same
frequency. Go to the Settings Menu/Wireless Channel on any other display/
keypad and select another channel. Note that after you change the channel you
will have to "re-teach" every wireless remote device in the system.
9.
Teach Wireless needs
to be run
This is caused by the remote not knowing the ID code of the base station. Run
the "Teach Wireless" procedure from any other direct wired display/keypad.
7
Settings
Menu
Teach Wireless:
+ to start
Teach Wireless:
Successful
Press and hold
wireless button
