background image

8

 

Installation/Operation & Maintenance Manual 
HFL4140E 4-POST ALIGNMENT LIFT

 

DANGER: 

indicates imminent danger that can result 

in serious injury to people or death. 

WARNING: 

indicates  situations  and/or  types  of 

maneuvers that are unsafe and can cause more or 
less harmful injuries or death. 

CAUTION: 

indicates  situations  and/or  types  of 

maneuvers  that  are  unsafe  and  can  cause  minor 
injury to persons and/or damage the lift, the vehicle 
or other property. 

RISK  OF  ELECTRIC  SHOCK: 

a  specific  safety 

notice  placed  on  the  lift  in  areas  where  the  risk  of 
electric shock is particularly high. 

RISKS AND PROTECTION DEVICES 

We  shall  now  examine  the  risks  that  operators  or 
maintenance  fitters  may  be  exposed  to  when  the 
vehicle  is  standing  on  the  platforms  in  the  raised 
position,  together  with  the  various  safety  and 
protection  devices  adopted  by  the  manufacturer  to 
reduce all such hazards to the minimum: 

LONGITUDINAL MOVEMENTS 

Longitudinal  movements  refer  to  forward  and 
backward movement of the load (vehicle). 

To protect against the consequences of longitudinal 
movement, the lift is installed with fixed wheel stops 
at the front of the lift, and pivoting stops at the rear. 
The stops are integral with the platforms and serve 
to  secure  the  vehicle  during  lifting  and  lowering 
movements and when the vehicle is at a standstill in 
the  raised  position,  thus  preventing  any  potentially 
dangerous movement. 

SIDE MOVEMENTS 

Side  movements  refer  to  shifting  of  the  vehicle 
toward  the  left  or  right  of  the  lift,  especially  during 
the lifting cycle. 

 

Fig. 12

 

 

Fig. 13

 

For  optimal  personal  safety  and  safety  of  vehicles, 
observe the following regulations: 

Do  not  enter  the  danger    zone  while  vehicles  are 
being lifted 

(see Fig. 11)

;

 

Switch off the engine of the vehicle, engage a  gear 
and engage the hand brake; 

Make  sure  the  vehicle  is  positioned  correctly 

(Fig.14)

 

Fig. 14 

Be sure to lift only approved vehicles, never exceed 
the  specified  carrying  capacity,  maximum  height, 
and projections (vehicle length and width); 

Make  sure  that  there  are  no  persons  on  the 
platforms  during  up  and  down  movements  and 
during standing 

(Fig. 15)

Summary of Contents for HFL4140E









































Reviews: