Haussmann RFLNS Installation & Operation Manual Download Page 5 | Manualshive

Page: 5 / 64

background image

P/N 0387183_V

REVISION N — APRIL 2013
1. Inserted Joining Instructions,

Pages 1-8 - 1-22

REVISION M — MARCH 2013
1. Revised caution note on page 1-1; added to

Page 4-1.

REVISION L — AUGUST 2012
1. Updated instructions for moving case through

small doors, Section 1.

REVISION K — JULY 2012
1. Included instructions for clearing smaller store

entrances, Section 1. Ice cream note added to
Page 4-1.

REVISION J — APRIL 2012
1. Corrected Table of Contents, page iii.

REVISION I — NOT ISSUED

REVISION H — MARCH 2012
1. Amended Installing Drip Piping procedure,

Page 3-2.

REVISION G — MARCH 2010
1. Revised Installing Drip Piping procedure,

Pages 3-1 through 3-6.

REVISION F — DECEMBER 2009
1.  Changed shimming drawing, Page 1-3.
2.  Updated drip piping pitch, Page 3-1.
3.  Added page division lines for thermometer,

Page 4-3.

4. Added cleaning stainless steel rails,

Page 5-2.

5. Added heater front and rear drawing,

Page 6-3.

6. Updated warnings and cautions throughout
7. Added new back cover

REVISION E — JANUARY 2009
1. Added page division lines for thermometer,

Page 4-3.

2. Added heater front and rear drawing,

Page 6-3.

3. Changed shimming drawing, Page 1-3.

REVISION D — SEPTEMBER 2007
1. Added front panel text and illustration, Page

1-2.

2.  Clarified shimming directions, Page 1-3.
3.  Added RLT information throughout.
4.  Added note to remove bumper protective film,

Page 1-6.

5. Added information on Always*Clear™ glass,

page 5-1.

6. Removed reference to Anthony doors, Page

6-5.

7.  Added repairing aluminum coil, Page 6-12.
8.  Changed warranty page.
9.  Added Installation Tool List, Page iv.
10.  Added revision history, Page iv.

REVISION C — JUNE 2002
1. Added NSF information, Pages 1-1,4-2

through 4-4.

2. Sections 2 through 6 are completely

rewritten.

3. Changed warranty to March 15,2002.

Reach-In

HUSSMANN CORPORATION, BRIDGETON, MO 63044-2483 U.S.A.

Permit Number:

20-05195

«
...
3
4
5
6
7
...
»

Summary of Contents for RFLNS

































































Reviews:

No comments

Related manuals for RFLNS

Brand: Royston Pages: 4

Brand: Turbo Air Pages: 35

Brand: Hussmann Pages: 3

Brand: Hussmann Pages: 4

Brand: Hussmann Pages: 6

Brand: Hussmann Pages: 4

Brand: Hussmann Pages: 5

Brand: Hussmann Pages: 5

Brand: Hussmann Pages: 6

Brand: Hussmann Pages: 5

Brand: Hussmann Pages: 9

Brand: Hussmann Pages: 9

Brand: Hussmann Pages: 9

Brand: Hussmann Pages: 6

Brand: Hussmann Pages: 6

Brand: Hussmann Pages: 6

Brand: Hussmann Pages: 6

Brand: Hussmann Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands