Haussmann RFLNS Installation & Operation Manual Download Page 30 | Manualshive

Page: 30 / 64

background image

1-24

I

nstallatIon

P/N 0387183_V

U.S. & Canada 1-800-922-1919 • Mexico 1-800-890-2900 • WWW.HUSSMANN.COM

INSTALLING SPLASHGUARDS AND BRACKETS

(RLTM Cases)
To install splashguards and brackets:

1. Slide the splashguard support bracket’s small
flange into base rail slots. Next, slide the splashguard
retainer assembly under the case as shown.

2. Rotate the retainer assembly clockwise (from right
hand side) while pulling towards the front of the case,
until the forward most flange sits flush with the back
of the color panel.

3. Align the retainer assembly with and attach to the
support bracket using #10 screws. Then install a #8
screw through the color panel into the top retainer
flange.

DO NOT

place

shims

under

splashguard

brackeTs

.

Splashguards Installation

Splashguard

Splice Connector

Side
Detail

R L NS 5

A

1. S lide the splashguard support bracket's small flange into the

slots in the base rail. Then slide the splashguard retainer
assembly under the case as shown.

2. R otate the retainer assembly clockwise (from right hand side)

while pulling towards the front of the case until the forward
most flange sits flush with the back of the color panel.

3. Align the retainer assembly with and attach to the support

bracket using #10 screws. Then install a #8 screw through the
color panel into the top retainer flange.

R L NS 5

A

1. S lide the splashguard support bracket's small flange into the

slots in the base rail. Then slide the splashguard retainer
assembly under the case as shown.

2. R otate the retainer assembly clockwise (from right hand side)

while pulling towards the front of the case until the forward
most flange sits flush with the back of the color panel.

3. Align the retainer assembly with and attach to the support

bracket using #10 screws. Then install a #8 screw through the
color panel into the top retainer flange.

R L NS 5

A

1. S lide the splashguard support bracket's small flange into the

slots in the base rail. Then slide the splashguard retainer
assembly under the case as shown.

2. R otate the retainer assembly clockwise (from right hand side)

while pulling towards the front of the case until the forward
most flange sits flush with the back of the color panel.

3. Align the retainer assembly with and attach to the support

bracket using #10 screws. Then install a #8 screw through the
color panel into the top retainer flange.

1.

2.

3.

Permit Number:

20-05195

«
...
28
29
30
31
32
...
»

Summary of Contents for RFLNS

































































Reviews:

No comments

Related manuals for RFLNS

Brand: FRIGOGLASS Pages: 99

Sliding Glass Door Merchandise SMB-430

Brand: Master Bilt Pages: 2

Brand: Master Bilt Pages: 2

Brand: Arneg Pages: 155

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands