Haussmann Xpert 56655000, Instruction Manual And Safety Instructions

Page: 15 / 19

15
ACCESSORY
WARNING
Accessories other than these shown
below can lead to malfunction and
resulting injuries.
STANDARD ACCESSORY
Breather pipe plug .......................... 1
APPLICATIONS
Air source for pneumatic nailers and staplers.
WARNING Never use compressor for applications
other than compressor for pneumatic
nailer and stapler.
PRIOR TO OPERATION
1. Initial set-up
A) Read safety warnings before setting-up this compressor.
B) Use a screwdriver or similar tool to remove the cap on
the lower part of the cylinder. Insert the breather pipe plug all
the way to the bottom.
cylinder air vent
breather
pipe plug
fig.3
WARNING
Drain tank to release air pressure before
removing the breather pipe plug.
WARNING
Make sure air vent in breather pipe plug is
free from debris. If air vent is blocked
pressure can build in crankcase causing
damage to compressor and possible
personal injury.
Ensure the oil level in this compressor pump is adequate. If
the oil level is low, replenish oil through the filling hole so that
the amount of oil will come to the middle of the oil sight glass
according to the following OIL TYPE CHART.
OIL TYPE CHART
Ambient
Temperature
(°C)
10°C - 50°C -30°C -50°C
Non-detergent
oil
SAE15W40
Graded oil
For summer
use only
SAE5W50
Synthetic oil
For both summer
And winter use
2. Location
WARNING
In order to avoid damaging this compressor,
do not incline this compressor more than
10° in any direction.
Place this compressor at least 4 inches away from obstacles
that may prevent proper ventilation.
Do not place this compressor in an area:
- where there is evidence of oil or gas leaks.
- where flammable gas vapours or materials may be present.
- where air temperatures fall below 0°C (32°F) or exceed 35°C
(95°F).
- where extremely dirty air or water could be drawn into this
compressor.
NOTE: When operating or storing the compressor, set 4
Rubber bumpers downward
on the floor (Refer to fig. 1).
3. Gasoline engine
A) Review page 14, point #27 before fueling.
WARNING
Do not allow the engine or muffler to come in
contact with flammable vapours, combustible
dust, gases or other combustible materials. A
spark may cause a fire. Do not place this
compressor in an area where flammable gas
vapours may be present.
B) Read the engine manual accompanying this compressor
for correct engine start-up maintenance procedures.
C) Read and understand the safety labels located on this
compressor.
D) A minimum of 85 octane fuel is recommended for use with
this compressor. Do not mix oil with gasoline.
E) Use of clean, fresh, lead free gasoline should be used. Do
not use gasoline containing methanol or alcohol.
F) Check the engine oil level before starting (See engine
manual).
G) Fill the fuel tank according to the engine manual
instructions.
WARNING
Follow all fueling instructions in this manual.
Gasoline is extremely flammable, and gasoline
vapour can explode. Do not refuel fuel tank
while this compressor is running or hot. Never
smoke near gasoline, and keep other flames
and sparks away. Allow this compressor and
engine to cool down before refueling. Do not
refuel indoors or in a poorly ventilated area. Do
not fill fuel tank to point of overflowing. Always
refuel slowly to avoid the possibility of spilled
fuel which may cause a fire. Do not operate
this compressor if gasoline is spilled. Wipe this
compressor clean and move it away from the
spill. Avoid creating any ignition until the
gasoline has evaporated. Allow approximately
1/4” of tank space for fuel expansion. Always
store fuel away from this compressor while it is
running or hot. Always store gasoline in an
approved container.
H) Refer to the engine manual for all necessary
maintenance and adjustments.