Haulotte BilJax AS2100, Assembly Instructions Manual

Page: 15 / 16

STEP 13 - INSTALLING RAMP HAND RAILS (continued)
15
This drawing is the property of BilJax INC., Archbold, Ohio. This equipment was designed with
the understanding that the prints are loaned and will not be reproduced, copied, or used to assist in
making further drawing, apparatus or parts therof, and is to be returned unless otherwise specified.
UNLESS OTHERWISE SPECIFIED
THE FOLLOWING APPLY:
*DIMENSIONS ARE IN INCHES.
*TOLERANCES ARE AS FOLLOWS
FRACTION DECIMALS ANGLES
+/- 1/32" XX +/- .01 +/- 1/2
XXX +/- .005
*ALL WELDS ARE TO BE CONTINUOUS
3/16" FILLETS.
*ALL WELD FILLETS ARE TO
COMPLETELY FOLLOW THE JOINT
CREATED BY THE MATING SURFACES
OF PARTS JOINED.
SIZE
DWG NO. DATE
DR
BY
REV
BY
SCALE
REV
DATE
REVISION E.C.O. 'S
B
1:4
FINISH lbs.
907.56
WEIGHT
RAMP ASSY INST DWGS
10-25-19 ELB
STEP 3
MATERIAL SPECIFICATION
ARCHBOLD, OHIO 43502
COPYRIGHT
C
2017
STEP 3G
This drawing is the property of BilJax INC., Archbold, Ohio. This equipment was designed with
the understanding that the prints are loaned and will not be reproduced, copied, or used to assist in
making further drawing, apparatus or parts therof, and is to be returned unless otherwise specified.
UNLESS OTHERWISE SPECIFIED
THE FOLLOWING APPLY:
*DIMENSIONS ARE IN INCHES.
*TOLERANCES ARE AS FOLLOWS
FRACTION DECIMALS ANGLES
+/- 1/32" XX +/- .01 +/- 1/2
XXX +/- .005
*ALL WELDS ARE TO BE CONTINUOUS
3/16" FILLETS.
*ALL WELD FILLETS ARE TO
COMPLETELY FOLLOW THE JOINT
CREATED BY THE MATING SURFACES
OF PARTS JOINED.
SIZE
DWG NO. DATE
DR
BY
REV
BY
SCALE
REV
DATE
REVISION E.C.O. 'S
B
1:4
FINISH lbs.
849.11
WEIGHT
RAMP ASSY INST DWGS
10-25-19
ELB
STEP 3
MATERIAL SPECIFICATION
ARCHBOLD, OHIO 43502
COPYRIGHT
C
2017
STEP 3E
1/8 SCALE
STEP 3F
1/8 SCALE
This drawing is the property of BilJax INC., Archbold, Ohio. This equipment was designed with
the understanding that the prints are loaned and will not be reproduced, copied, or used to assist in
making further drawing, apparatus or parts therof, and is to be returned unless otherwise specified.
UNLESS OTHERWISE SPECIFIED
THE FOLLOWING APPLY:
*DIMENSIONS ARE IN INCHES.
*TOLERANCES ARE AS FOLLOWS
FRACTION DECIMALS ANGLES
+/- 1/32" XX +/- .01 +/- 1/2
XXX +/- .005
*ALL WELDS ARE TO BE CONTINUOUS
3/16" FILLETS.
*ALL WELD FILLETS ARE TO
COMPLETELY FOLLOW THE JOINT
CREATED BY THE MATING SURFACES
OF PARTS JOINED.
SIZE
DWG NO. DATE
DR
BY
REV
BY
SCALE
REV
DATE
REVISION E.C.O. 'S
B
1:4
FINISH
lbs.
907.56
WEIGHT
RAMP ASSY INST DWGS
10-25-19 ELB
STEP 3
MATERIAL SPECIFICATION
ARCHBOLD, OHIO 43502
COPYRIGHT
C
2017
STEP 3G
This drawing is the property of BilJax INC., Archbold, Ohio. This equipment was designed with
the understanding that the prints are loaned and will not be reproduced, copied, or used to assist in
making further drawing, apparatus or parts therof, and is to be returned unless otherwise specified.
UNLESS OTHERWISE SPECIFIED
THE FOLLOWING APPLY:
*DIMENSIONS ARE IN INCHES.
*TOLERANCES ARE AS FOLLOWS
FRACTION DECIMALS ANGLES
+/- 1/32" XX +/- .01 +/- 1/2
XXX +/- .005
*ALL WELDS ARE TO BE CONTINUOUS
3/16" FILLETS.
*ALL WELD FILLETS ARE TO
COMPLETELY FOLLOW THE JOINT
CREATED BY THE MATING SURFACES
OF PARTS JOINED.
SIZE
DWG NO. DATE
DR
BY
REV
BY
SCALE
REV
DATE
REVISION E.C.O. 'S
B
1:4
FINISH lbs.
849.11
WEIGHT
RAMP ASSY INST DWGS
10-25-19 ELB
STEP 3
MATERIAL SPECIFICATION
ARCHBOLD, OHIO 43502
COPYRIGHT
C
2017
STEP 3E
1/8 SCALE
STEP 3F
1/8 SCALE
E
F
G
E) Insert 4’ hand rail tube into end of upper hand rail and rotate so the L-bolts are in the slots of
guard rail. Loosely attach hex nuts. Repeat until reaching ramp end guard rail.
F) Insert lower hand rail into 4’ hand rail tube and rotate so the L-bolts are in the slots of ramp
end guard rail. Loosely attach hex nuts.
G) Insert end of hand rail support return into end of lower hand rail and rotate so the saddle is
around tube of guard rail. Insert bolt and attach and tighten hex nut.
H) Repeat steps for hand rails on other side of ramp.
I) Thoroughly tighten all hex nuts.
! WARNING ! – Failure to correctly install hand rails could result in serious injury or death. Verify
that all hex nuts are tightened.