Haulotte Group H14TX Maintenance Book Download Page 83

Page: 83 / 120

4000364740

E12.16

USA / GB

Control-Filling-up-Battery charge

Battery

E018

10 min

Control-Filling-up-Battery charge

Battery

1 - You will need

2 - Preliminary procedure

Place the machine in maintenance configuration.

3.3.1-Placing the machine in maintenance

configuration

3 - Control

Loosen the caps located on the top of the battery.

The level of electrolyte in the battery must be approx. 0,01 m(0 ft39 in) above the plates.

4 - Filling-up

• Standard tool kit
• Protective goggles
• Gloves

• Place barriers around the perimeter of the
work area

The battery manufacturer's safety instructions must be followed.

Loosen the caps located on the top of the battery.

If the level of electrolyte is below the level of the plates :

Top up with distilled water.

Refit and tighten the battery caps.

Summary of Contents for H14TX

























































































































Search results

Summary of Contents for H14TX

Reviews:

Related manuals for H14TX

Brands by name

Popular brands

Haulotte Group H14TX, Maintenance Book

Search results

Summary of Contents for H14TX

Reviews:

Related manuals for H14TX

Brands by name

Popular brands