background image

SPECIFICATIONS

Note: All specifi cations are subject to change without prior notice!

Please visit www.hattelandtechnology.com for the latest electronic version.

2/2

2/6

Button layout and functions:

1      2      3

Status RGB LED

ID

Visual

Simulates

Description

Requires

Physical Operation

1

Decrease / Brightness Negative -

In Normal Mode Press button and release

2

Power Control, configured as ON / OFF

In Normal Mode

Press and hold down

button at least 3 seconds

3

Increase / Brightness Po

In Normal Mode Press button and release

1

Arrow Left, configured as Navigation Back

or as Hot Key #1

In Menu Mode

2

OSD Menu Access, configured as Show/Hide

In Menu Mode

3

Arrow Right, configured as Navigation Forward

 or as Hot Key #2

In Menu Mode

-

-

Performs factory reset of the Remote Control

In OFF Mode

Press buttons and hold at 

least 10 seconds

-

-

Switches between Normal and Menu Mode as

default configuration on exiting from OFF mode

In OFF Mode

Press buttons and hold at 

least 5 seconds

-

-

Turns on or off Status RGB LED visibility as

default configuration on exiting from OFF mode

In OFF Mode

Press buttons and hold at 

least 5 seconds

-

-

Status RGB LED to indicate mode to user and

behaviour for the Remote Control

None

The Remote Controller is designed to simulate the regular 6-button available on the Glass Display Control (GDC™) 

as default available on all Series X products via a timer-based configuration explained as "Normal" and "Menu" 

mode for the Remote Control, all these 6 buttons can be accessed and simulated at the same time, based on a 

user intervention such as On-button-first-press (On Down), press-and-hold or just press-and-release on any of the 

physical buttons.

1      2      3

1      3               2

Prior to using the Remote Control, the communication mode RS-485 (4-wire) must be configured and the monitor unit's RS adress must be set to "0". Two ways 

are possible, either by OSD or by SCOM. 

Only the unit with address '0' allows OSD Menu control over remote controller. The units with other addresses do not 

support OSD menu control. Normally, the address of each unit on the same bus, has to be unique. 

Series X Generation 1 - HD xxT21 MMD

To get access, first change menu mode:

1: OSD Settings > OSD Mode > Full > (Radio Button) and Enter Key Code “362”

2: Management Settings > Communication > 4-wire RS485/422 > (Radio Button)

3: Management Settings > Communication > Address RS > (Slider Bar)

Series X Generation 2 - HD xxT22 MMD

To get access, first change from "Basic Mode" to "Advanced Mode":

1: OSD Miscellaneous > OSD Mode > Advanced > (Select) and Enter Key Code "362"

2: Management Settings > Communication > 4-wire RS485/422 > (Select)

3: Management Settings > Communication > Address RS > (Slider Bar 0~15)

Series X Generation 1 - HD xxT21 STD

To get access, first change menu mode:

1: OSD Misc > OSD Mode > Full > (Radio Button) and Enter Key Code “362”

2: Management > Communication > 4-wire RS485/422 > (Radio Button)

3: Management > Communication > Address RS > (Slider Bar)

Multi Vision Display / MIL - HD xxT22 MVD / HM xxT22 RMD,HM xxT22 CMD:

To get access, first change from "Basic Mode" to "Advanced Mode":

1: OSD Menu > OSD Mode > Advanced> (Select) and Enter Key Code “362”

2: Communication > 4-wire RS485/422 > (Automatic Action)

3: Communication > Address RS > (Slider Bar)

Via SCOM Command (applicable for all units / product ranges above): 

Send Bytes (shown here as HEX, 30= value "0"): 07 FF 4D 43 43 02 24 BB 30 14

Configuration of monitor unit:

Reviews: