29
Serial/Ethernet Communication (SCOM) Interface
IND100084-14
MCC Command
Syntax and Functionality
Details and Values
Graphic Vertical Sync.
Frequency
Send Only : 07 FF 4D 43 43 01 25
BA
45
Available response status:
"xxx" = where xxx is a 3-digit HEX
number indicating frequency in units
of 0.1Hz + 1 character indicating
field mode as:
"i" = Interlaced
"p" = Progressive
Example:
"256p" = 598 (59.8 Hz),
progressive fields
Address RS (Serial)
Range 0-15
Syntax : 07 FF 4D 43 43 02 24
BB
xx
zz
Function Examples:
Example "9" : 07 FF 4D 43 43 02 24
BB
39
0B
Where
xx
= "0" to "F"
Where
zz
= Calculated Checksum
Address RS (Serial)
Extended Range 0-254
Syntax : 07 FF 4D 43 43 02 24 7D
xx
yy
zz
Function Examples:
"address 254" : 07 FF 4D 43 43 02 24 7D
FE
84
Query "?" : 07 FF 4D 43 43 02 24 7D
FF
3F
44
Reset "R" : 07 FF 4D 43 43 02 24 7D
FF
52
31
Reset "r" : 07 FF 4D 43 43 02 24 7D
FF
72
11
*[1] - See comment
Where
xx
= 0x00 - 0xFF
Where
yy
= Query/Reset byte, only
when
xx
= 0xFE. Otherwise skip.
Where
zz
= Calculated checksum
Set IP Address (fixed or auto)
Note:
By sending this command, the
communication mode will be
automatically set to "Ethernet",
in the
"Communication Mode"
,
referenced earlier in this chapter.
In addition, a power off/on to
the unit is required to reboot the
internal network code and utilize
the newly set IP address. This
can either be done by issue the
"Power down / up"
command
described earlier in this table or
do a physical power off/on for
the unit.
Syntax : 07 FF 4D 43 43 10 16
BC
v1 v2 v3
2E
w1
W2 W3
2E
x1 x2 x3
2E
y1 y2 y3
zz
Function Examples:
Example fixed IP 192.168.1.35, Send:"192.168.001.035":
07 FF 4D 43 43 10 16
BC
31 39 32
2E
31 36 38
2E
30 30
31
2E
30 33 35
55
Set Auto IP "A" : 07 FF 4D 43 43 02 24
BC
41
02
Set Auto IP "a" : 07 FF 4D 43 43 02 24
BC
61
E2
Where
v1
= "0" to "2"
Where
v2
= "0" to "9"
Where
v3
= "0" to "9"
Where
w1
= "0" to "2"
Where
w2
= "0" to "9"
Where
w3
= "0" to "9"
Where
x1
= "0" to "2"
Where
x2
= "0" to "9"
Where
x3
= "0" to "9"
Where
y1
= "0" to "2"
Where
y2
= "0" to "9"
Where
y3
= "0" to "9"
Where 2E = "." (dot)
Where
zz
= Calculated Checksum
or
Where
v1
= "a" or "A" (Auto IP)
Where
zz
= Calculated Checksum
Available response status:
"0" = Fail
"1" = Successful
Auto Position
Send Only : 07 FF 4D 43 43 01 25
C3
3C
Available response status:
"0" = Fail
"1" = Successful
Auto Color Balance
Send Only : 07 FF 4D 43 43 01 25
C5
3A
Available response status:
"0" = Fail
"1" = Successful
OSD Outdoor Mode
Syntax : 07 FF 4D 43 43 02 24
CA
xx
zz
Function Examples:
Example "1" : 07 FF 4D 43 43 02 24
CA
31
04
Where
xx
= "0" to "1"
Where
zz
= Calculated Checksum
Available functions:
"0" = No delay for all touch
buttons, except 2 sec delay
for "MENU"
"1" = Delay 5 seconds for all touch
buttons
*[1] RS Address (extended):
The command is extended command Address configuration of RS485 configuration. It provides the same
function as MCC 0xBB, but with two differences:
- Extended command MCC 0x7D is able to set address from 0x00 to 0xFE
- Extended command data byte in heximal format.
This command update the same data byte in EEPROM and OSD status package as MCC 0x7D.
Reference Engineering Change Notification:
https://www.hattelandtechnology.com/product-notifications/firmware-update-affecting-series-x-mmd/std-displays-12-to-26-inch
