![background image](http://html1.mh-extra.com/html/hatco/07-04-388-00/07-04-388-00_installation-and-operating-manual_2107086008.webp)
8
Form No. TCDONM-0713
MAINTENANCE
General
The Edward Don Electric Conveyor Toasters are designed for
maximum durability and performance, with minimum
maintenance.
ELECTRIC SHOCK HAzARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning, setup, or
maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use jet-
clean spray to clean this unit.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
This unit has no “user-serviceable” parts. If service is
required on this unit, contact an Authorized Hatco Service
Agent or contact the Hatco Service Department at 800-558-
0607 or 414-671-6350; fax 800-690-2966; or International fax
414-671-3976.
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
Use non-abrasive cleaners only. Abrasive cleaners could
scratch finish of unit, marring its appearance and making
it susceptible to soil accumulation.
NOTICE
WARNING
Daily Cleaning
For sanitary operation as well as to preserve the condition of
the unit and maintain performance, it is recommended that the
unit be cleaned daily.
1. Switch OFF (O) the HEaT ON/OFF switches and allow the
unit to cool completely.
2. Remove, empty, and clean the crumb tray and the
discharge chute.
• Wash with warm water and a mild detergent. Rinse with
water.
• allow to air dry or hand dry with a soft cloth before
placing back into the toaster.
3. Remove and clean the feed ramp. To remove, squeeze
inward on the two wire spokes that attach the feed ramp to
the unit.
• Wipe clean with a soft, damp cloth or soak the guide in
a mild solution of 1 cup ammonia and 1 gallon of water
(227 milliliters and 3.785 liters).
4. Wipe the exterior surface of the toaster with a damp cloth.
Stubborn stains may be removed with a good stainless
steel cleaner or a non-abrasive cleaner. Hard to reach
areas should be cleaned with a small brush and mild soap.
Additional Cleaning
Over an extended period of use, bread crumbs may buildup on
the reflector. The following steps are recommended to preserve
the condition of the unit and maintain performance.
1. Switch OFF (O) the HEaT ON/OFF switches and allow the
unit to cool completely.
2. Remove crumb buildup on the bottom heating reflector.
• Wipe crumbs onto the crumb tray using a bristle brush.
NOTE: The conveyor gear motor and conveyor system are
permanently lubricated and require no lubrication.
Troubleshooting Questions?
If you continue to have problems resolving an issue, please
contact the nearest authorized Hatco Service agency or Hatco
for assistance. To locate the nearest Service agency, log onto
the Hatco website at
www.hatcocorp.com
and click on
Find Service Agent
, or contact the
Hatco Parts and Service
Team
at:
Telephone: 800-558-0607 or 414-671-6350
e-mail:
Fax:
800-690-2966 or 414-671-3976