Hasselblad 503CX Manual Download Page 39

Page: 39 / 42

Troubleshooting

Your camera is built to give long and trouble-free service. If however you encounter any operating difficulties

because you are not familiar with the Hasselblad camera system, the following table may help to resolve them.

PROBLEM

POSSIBLE CAUSE

REMEDY

You cannot operate the

release button

Remove the slide

The magazine slide is still in

place

The release button

remains depressed

The time exposure lock is in

the T-position

The film is finished

Load a new film

The camera is in the released

position

Wind the camera

Return the lock to the

O-position

There is no image on the

focusing screen

The camera is in the pre-re-

leased or released position.

The camera is in the pre-re-

leased or released position.

The camera is in the pre-re-

leased or released position.

The camera is in the pre-re-

leased or released position.
The lens shutter is in the

released position

Release and/or wind the

camera

Release and/or wind the

camera

Release and/or wind the

camera

Release and/or wind the

camera

You cannot remove the

front protective cover

You cannot attach the

lens

You cannot remove the lens

You cannot remove the

magazine

The magazine slide is not fully

inserted

Insert the magazine slide until it

is positively stopped

Summary of Contents for 503CX











































Search results

Summary of Contents for 503CX

Reviews:

Related manuals for 503CX

Brands by name

Popular brands

Hasselblad 503CX, Manual

Search results

Summary of Contents for 503CX

Reviews:

Related manuals for 503CX

Brands by name

Popular brands