background image

22

Super-Magnum Coal Stoker Stove

Do Not Burn Wet Coal!

3-90-02702R4_08/12                                                       

C.  Before Your First Fire

•  Be  sure  the  appliance  is  installed  properly  and 

that  all  safety  requirements  have  been  met. 

Pay  particular  attention  to  the  clearances  to 

combustibles,  floor  protection  and  the  venting 

instructions.

•  Test your smoke detector(s) and CO detector(s) to 

the specifications of the manufacturer.

•  Double check that the ash pan and internal firebox 

are empty.

•  Be sure to read this entire manual.

D.  Starting Your First Fire

1.  With the mode selector in the "OFF" position, and 

the Feed Adjuster 

NOT

 on "Test", plug the power 

cord into a properly grounded receptacle.

2.  Fill the hopper with DRY coal. 

3.  Place some coal on the burn grate, filling the valley 

in the back. 

4.  Turn the mode selector dial to the desired mode. 

If  Room  Temp  is  selected,  be  sure  to  turn 

the  temperature  dial  above  the  current  room 

temperature.

5.  Fill the rest of the grates with a mixture of wood 

pellets, rice coal, and starting gel.

6.  Light the starting gel with a match, and close the 

door. 

7.  Only after the ESP temperature increases, will the 

feeder start operating to increase the fire size.

NEVER APPLY STARTING GEL TO THE STARTING 

MIXTURE WITHOUT THE COMBUSTION BLOWER 

OPERATING.

WARNING

"NEVER USE GASOLINE, GASOLINE-TYPE 

LANTERN FUEL, KEROSENE, CHARCOAL 

LIGHTER FLUID, OR SIMILAR LIQUIDS TO 

START OR "FRESHEN UP " A FIRE IN THIS 

HEATER. KEEP ALL SUCH LIQUIDS WELL 

AWAY FROM THE HEATER WHILE IN USE".

E.  Fire Characteristics

After lighting the fire, it will go through a few different 

stages  of  appearance.  First,  because  of  the  wood 

pellets mixed in, you'll see mostly tall yellow flames. 

As the wood pellets burn away, and some coal begins 

to ignite, your yellow flames will shorten and mix with 

blue flames. After the wood pellets are gone and the 

coal is the only thing burning, you'll see mostly blue 

flames, which can be invisible in a brightly lit area. As 

the fire settles in, you'll have about a two inch band 

of hot burning coals running across the grates. With 

a maximum temperature demand, the ideal feed rate 

setting  will  put  this  band  approximately  1-2  inches 

back from the end of the grates. Allow at least an hour 

of burn time between adjustments to the feed rate.

The setting above will produce continuous maximum heat output 

with the distribution blower at full speed.

The setting above will produce continuous medium heat output with 

the distribution blower at low speed.

Summary of Contents for Super-Magnum Coal Stoker Stove









































Reviews: