Harman P61 Owner'S Manual Download Page 13

 13

when to use "Stove Temp Mode"

In "Stove Temp Mode" the Stove Temp Dial determines 

the temperature of the stove. Heat output and fuel 

consumption will remain constant. This makes it 

possible to tell how long a hopper full of pellets will last. 

The distribution blower speed will vary according to the 

position of the mode selector, fig. 21.

when to use "room Temp Mode"

In "Room Temp Mode" heat output is controlled 

automatically by the Room Sensing Probe. When 

the Room Sensing Probe calls for heat, the stove will 

increase output. When the Room Sensing Probe is 

getting close to the set temperature, the stove will begin 

to level off output and keep the fire burning at just the 

right temperature to maintain that setting.

High output is determined by the feed rate. The 

maximum feed rate should be set for 1" of ash in front 

of fire.

In "Room Temp Mode" fuel consumption is sacrificed 

for exact room temperature. Therefore, as it gets colder, 

more pellets will be burned automatically.

The distribution blower speed will vary according to 

the position of the mode selector, fig. 21.

Shut-down Procedure

To kill the fire or stop burning the stove, turn the Mode 

Selector to "OFF". This will cause the fire to diminish 

and burn out. When the fire burns out and the stove 

cools down everything will stop.

Never pull the plug to shut down the stove, all motors 

will stop. This will cause incomplete combustion and 

smoke in the firebox. If the load door is opened the 

smoke will escape.

The best way to shut down the stove is to simply 

let it run out of pellets, then the stove will shut down 

automatically.

MANuAl  IgNITION/OPErATION

This setting will produce medium heat with the distribution 

blower on "low".

Fig. 21

This setting will produce a room temperature of 70 

degrees with the distribution blower at medium speed.

This setting will produce continuous maximum heat output 

with the distribution blower at full speed.

Summary of Contents for P61

























Reviews: