background image

7

PP38+ Pellet Stove

3-90-08422R33_06/13

venting

requirements for terminating the venting
warning:

 Venting terminals must not be recessed into a 

wall or siding.

note:

 Only approved pellet vent pipe, wall pass-throughs, 

and  fire  stops  should  be  used  when  venting  through 

combustible materials.

note:

 Always  take  into  consideration  the  effects  of  the 

prevailing  wind  direction  or  other  wind  currents  that  may 

cause flyash and/or smoke when placing the termination of 

the vent.

in addition, the following must be observed:

A. The clearance above grade  must be a minimum of 18".
B. The clearance to a window or door that may be opened 

must  be  a  minimum  of  48"  to  the  side,  48"  below  the 

window/door,  and  12"  above  the  window/door.

 

(

with 

outside air installed, 18” to the side or below

)

C. A  12"  clearance  to  a  permanently  closed  window  is  

recommended to prevent condensation on the window.

D. The vertical clearance to a ventilated soffit located above 

the terminal within a horizontal distance of 2 feet (60 cm) 

from the center-line of the terminal  must be a minimum 

of 18".

E. The clearance to an unventilated soffit  must be a minimum 

of 12".

F.  The clearance to an outside corner is 11" from center of 

pipe.

G. The clearance to an inside corner is 12".
H. A vent must not be installed within 3 feet (90 cm) above 

a gas meter/regulator assembly when measured from the 

horizontal center-line of the regulator.

I.  The clearance to service regulator vent outlet must be a 

minimum of 6 feet.

J.  The clearance to a non-mechanical air supply inlet to the 

building or the combustion air inlet to any other appliance 

must be a minimum of 48”.

K. The clearance to a mechanical air supply inlet must be a 

minimum of 10 feet.

 

(

with outside air installed, 6 feet 

)

L.  The  clearance  above  a  paved  sidewalk  or  a  paved 

driveway located on public property must be a minimum 

of  7 feet.

M. The clearance under a veranda, porch, deck or balcony 

must be a minimum of 12 inches.

 

(

b. also applies

)

note:

  The  clearance  to  vegetation  and  other  exterior 

combustibles such as mulch is 36” as measured from the 

center of the outlet or cap. This 36” radius continues to grade 

or a minimum of 7 feet below the outlet.
Certain Canadian and/or  Local codes or regulations may 

require different clearances.
A  vent  shall  not  terminate  directly  above  a  side-walk  or 

paved driveway which is located between two single  family 

dwellings and serves both dwellings.
Only permitted if veranda, porch, deck, or balcony is fully 

open on a minimum of  2 sides beneath the floor.

note: where passage through a wall, or partition of 

combustible construction is desired, the installation 

shall conform to can/csa-b365. (if in  canada)

V

=Vent Terminal

A

=Air Supply Inlet

=Area where termination is mot permitted

Door

Sidewalk

Fixed

Closed

Openable

Openable

Fixed

Closed

Inside Corner

Detail

Porch or

Openable

Deck 
or Fixed

Summary of Contents for P38plus







































Reviews: