background image

3

PP38+ Pellet Stove

3-90-08422R33_06/13

Safety Information     

 

 

5

Installation   

 

 

 

6

Venting 

 

 

 

 

8

ESP Control              

 

 

15

Operation   

 

 

 

16

Draft Test Procedure 

 

 

19

Maintenance  

 

 

 

20

Troubleshooting 

 

 

 

25

Specifications 

 

 

 

26

Options 

 

 

 

 

27

Corn/Pellet Mixture   

 

 

28

Fuel Specification Details   

 

29

Wiring Diagram 

 

 

 

30

Warranty 

 

 

 

 

31

Service Parts  

 

 

 

33

table of contents

introduction

Safety Listing: Omni-Test Laboratories, Inc.

Report # 135-S-21-6.2

Tested to: ASTM E1509-04, ULC S627-00, and 

ULC/ORD-C1482-M1990. 

This appliance is also approved for installation 

into a shop.

Division of Hearth & Home Technologies

352 Mountain House Road

Halifax, PA 17032

warning

do not connect to anY air distribution duct 

or sYsteM.

warning

do not use cheMicals or Fluids to start the 

Fire. do not burn garbage or FlaMMable 

Fluids such as gasoline, naPtha, or oil.

This label is located on the back of the unit. 

Please copy the Serial Number for future reference.

Serial #:

"PREVENT HOUSE FIRES"

Install and Use Only in Accordance With Manufacturer's Installation and Operation Instructions.

Contact Local Building or Fire Offi cials About Restrictions and Installation Inspection in Your Area.
WARNING : THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL,

AND CEILING/ROOF MUST BE MAINTAINED. DO NOT INSTALL IN SLEEPING ROOM.
An outside combustion air inlet must be provided. Refer to Manufacturer’s instructions and local

codes regarding the requirements for passing the exhaust venting system through a combustible

wall or ceiling.
Inspect and Clean Exhaust Venting System Frequently.

Use a 3" or 4" diameter type "L" or "PL" venting system.
Do Not Connect This Unit to a Chimney Flue Serving Another Appliance.

FOR USE WITH WOOD PELLET FUEL OR UP TO 50% CORN / PELLET MIXTURE ONLY.

The Use of Other Fuels May Create an Unsafe Condition.

Input Rating Max: 5.5 lb. fuel/hr.
U.S. Electrical Rating: 115 VAC, 60 Hz, Start 4.2 AMPS, Run 2.8 AMPS

Route Power Cord Away From Unit.

DANGER: Risk of Electrical Shock. Disconnect Power Before Servicing Unit.
For Further Instruction, Refer To Owner's Manual.
Replace glass only with 5mm ceramic available from your dealer.
Keep Viewing and Ash Removal Doors Tightly Closed During Operation.

DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ÉTIQUETTE

MINIMUM CLEARANCES TO COMBUSTIBLES/

DISTANCES DE SECURITE PAR RAPPORT AUX

MATERIAUX COMBUSTIBLES:

Back Wall / Entre Mur Arrière   2”/ 51mm 

2”/ 51mm

Side Wall / Entre Paroi Latér 

16”/ 406mm 

10”/ 254mm

CORNER INSTALLATION / EN ANGLE

Walls to Appliance  

9”/228mm 

9”/228mm

Entre Murs et appareil

Flue Connector/Raccord à la cheminée     3” /76mm
FLOOR PROTECTION / Protection Du Plancher

 

     USA Canada

Sides*/Côtés   (A)     6” 

200mm

Back**/Arrière (B)     6” 

200mm

Front*/Avant   (C)     6” 

450mm

**Measured from pedestal base in the US ONLY

**Mesuré à partir de la base du socle aux États-Unis uniquement

*Measured from Glass Opening

*Mesurer à partir de la surface de la porte en verre
Floor Protection Must Be a Non-Combustible Material.

Must  Also  be  Place  Under  Any  Horizontal  Flue  Connector, 

Extending 2” or 51mm Beyond the Pipe Measurement.

Pour protéger le plancher, il faut sous le pêole un matériau. Qui 

doit aussi être placé sous les parties horizontales du tuyau de 

raccord à la cheminée et s’étendre à 51mm o 2 po. au-delà de 

la mesure du tuyau.

Made in U.S.A. of US and imported parts. / Fabriqué

aux États-Unis-d’Amérique par des pièces d’origine

américaine et pièces importées.

"PREVENTION DES INCENDIES"

Respecter scrupuleusement les instructions du constructeur pour l'installation et les consignes

de fonctionnement. Respecter les règles de sécuritè en vigueur dans votre région.

AVERTISSEMENT POUR MOBILE HOMES:

 Ne pas installer dans une chambre. ll est imperatif

de prévoir une prise d'alr extérieur. L'intégrité structurale du plancher, du plafond et des murs doit étre

strictement préservée. Se reporter aux instructions du fabricant et aux réglementations spécifi ques

locales concernant les précautions requises lors de la traversée d'un mur ou d'un plafond.

Contróler et nettoyer fréquemment tout le systeme d'evacuation des fumées conformément aux

recommandations du constructeur. Utiliser des tuyaux <<Spécial granulés>> de Ø76 mm ou

102 mm. Ne pas raccorder ce poéle à un conduit de cheminée déjà utilisé pour un autre appareil.

FONCTIONNE EXCLUSIVEMENT AVEC DES GRANULES DE BOIS

.

Appareil de chauffage à granulé type. Consommation maximum: 2.5 kg/h.

US coupure: 115 VAC, 60 Hz, 4.2 amps Démarrer, Exécuter 2.8 AMPS

fonctionnement normal 1.1A. Tenir le cordon d'alimentation à l'écart du poèle.

DANGER: Risque d'électrocution. Débrancher l'appareil avant toute intervention.

Ne remplacer la vitre qu'avec une vitre céramique 5mm de méme qualité disponible

auprès de votre revendeur.

Pour une information plus compléte, se reporter à la notice d'utilisation. Tenir la porte

hermétiquement close durant fonctionnement.

Ne faites pas obstacle l’espace sous le réchauffeur. Toujours fournir un approvisionnement suffi sant en air frais 

jusqu’au lieu d’installation Appliance

BARCODE LABEL

Date of Manufacture / Date de fabrication:

P.N. 3-90-04300

WITHOUT

SIDE SHIELDS

WITH

SIDE SHIELDS

Sans Écrans

Latéraux

Avec Écrans

Latéraux

Fabriqué par: Harman Stove Company 352 Mountain House Road, Halifax PA 17032

US ENVIRONMENTAL PROTECTION AGENCY

This model is exempt from EPA certifi cation under 40 CFR 60.531

by defi nition [Wood Heater (A) "Air-to-Fuel Ratio"]

Agence Américaine pour la Protection de l’Environnement

Ce modéle est dispensé par EPA certifi cation d’aprés 40 CFR 60.531

par dèfi nition [Appareil á bois (A) << Ratio air/combustible>>]

2012   2013   2014   jan   Feb   Mar   aPr   MaY   jun   jul   aug   seP   oct   nov   dec

Harman PP38+/P43 Pellet Stove

Label measures: 4-3/8" high X 10-3/4"wide

Black Background with bare metal for print-adhesive backed, metal plate.

008

Serial No.

N

o

 de série:

Report #/ Raport # 135-S-21-6.2 (PP38+)

Report #/ Raport # 135-S-23b-6.2 (P43)

Tested to / Testé à:

ASTM E1509-04, ULC/ORD-C1482-

M1990, ULC-S627-00

Room Heater Pellet Fuel Burning Type. Also for use in Mobile Homes.

Appareil de chauffage à granulés de bois Utilisable dans des mobile homes. 

This pellet burning appliance has been tested and listed for use in Manufactured 

Homes in accordance with OAR 814-23-900 through 814-23-909

MODEL / MODÈLE:      "PP38+ /       P43"

2"(51mm)

10" (254mm) with side shields

16" (406mm) w/out side shields

a

a

c

b

usa

canada

F

loor

 

protector

Protection de sol

Floor Protection

9"(228mm) 

9"(228mm)

3" min

76mm min
3" min

76mm min

rev c

= contains updated information

Summary of Contents for P38plus







































Reviews: