background image

1.IMPORTANT SAFETY INSTRUCTIONS  

This  symbol  is  intended  to  alert  you  to  the 
presence  of  uninsulated  dangerous  voltages 
within the product’s enclosure that may be of 
sufficient  magnitude  to  constitute  a  risk  of 
electric shock.  

This symbol is used throughout this manual and 
is  intended  to  alert  you  to  the  presence  of 
important instructions.   

1) Read these instructions.  

2) Keep these instructions.  

3) Heed all warnings.  

4) Follow all instructions.  

5) Do not use this apparatus near water.  

6) Clean only with dry cloth.  

7) Do not block any ventilation openings. Install in 
accordance with the manufacturer’s instructions.  

8) Do not install near any heat sources such as radiators, 
heat  registers,  stoves,  or  other  apparatus  (including 
amplifiers) that produce heat.  

9) Do not defeat the safety purpose of the polarised or 
grounding-type plug. A grounding-type plug has two 
blades and a third grounding prong. The wide blade 
or the third prong are provided for your safety. If the 
provided plug does not  fit  into  your  outlet,  consult  an  
electrician  for replacement of the obsolete outlet.  

10)  Protect  the  power  cord  from  being  walked  on  
or pinched particularly at plugs, convenience receptacles, 
and the point where they exit from the apparatus.  

11)  Only  use  attachments/accessories  specified  by  the 
manufacturer.   

JBL Intellivox Installation Manual  

12) Use only with the cart, stand, tripod, bracket 
or table specified by the manufacturer, or sold 

with the apparatus. When a cart is used, use caution when 
moving the cart/apparatus combination to avoid injury from 
tip-over.  

13) Unplug this apparatus during lightning storms or when 
unused for long periods of time.  

14) Refer servicing to qualified service personnel. Servicing 
is required when the apparatus has been damaged in any 
way, such as power-supply cord or plug is damaged, liquid 
has been spilled or objects have fallen into the apparatus, 
the apparatus has been exposed to rain or moisture, does 
not operate normally, or has been dropped.   

Warning

 -To reduce the risk of fire or electric  

shock, do not expose this apparatus to rain or 

moisture and objects filled with liquids, such as vases, 
should not be placed on this apparatus.  

Warning

 - In order to disconnect this apparatus  

from  the  mains  power  supply,  the  connector 

should be removed from the mains socket located on the 
amplifier module.  

Warning

 - Do not expose the internal backup battery to 

excessive heat such as sunshine, fire or the like. 

Caution

 - Danger  of  explosion  if  the  internal  backup 

battery is incorrectly replaced. Replace only with the same 
or equivalent type.  

Warning

 - The installer should ensure that the  

mechanical mounting method employed should 

be capable of supporting four times the weight of the unit 
(i.e., with a safety factor of 4).  Always use all the brackets 
provided with the unit. Only skilled persons may install the 
units.  

Warning

 - This apparatus is a Class I device and 

must be connected to a mains socket outlet that provides a 
safety ground connection.  

202007/IvxIM_v2.3

Summary of Contents for JBL Professional Intellivox DS 115





























Reviews: