Harman AMX DX-TX-DWP-4K60-BL Hardware Reference Manual Download Page 2

 

 

Important Safety Instructions 

READ

 these instructions. 

KEEP

 these instructions. 

HEED

 all warnings. 

FOLLOW

 all instructions. 

DO NOT

 use this apparatus near water. 

CLEAN ONLY

 with dry cloth. 

DO NOT

 block any ventilation openings. Install in accordance with the manufacturer's instructions. 

DO NOT

  install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including 

amplifiers) that produce heat. 

PROTECT

 the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the 

point where they exit from the apparatus. 

ONLY USE

 attachments/accessories specified by the manufacturer. 

USE ONLY

 with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the 

apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid 
injury from tip-over. 

REFER

 all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in 

any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the 
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 
DO NOT EXPOSE THIS APPARATUS TO DRIPPING OR SPLASHING AND ENSURE THAT NO OBJECTS FILLED WITH 
LIQUIDS, SUCH AS VASES, ARE PLACED ON THIS APPARATUS. 

To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from 
the AC receptacle.

 

Where the mains plug or an appliance coupler is used as the disconnect device, the disconnect device 
shall remain readily operable.

   

DO NOT overload wall outlets or extension cords beyond their rated capacity as this can cause electric shock or fire. 

 

Summary of Contents for AMX DX-TX-DWP-4K60-BL















Reviews: