Harman Kardon CITATION 5.1 Owner'S Manual Download Page 21

Input/Output Protection

Under some conditions, such as a shorted speaker wire, DC voltage on an input
connection or thermal overload, the Citation 5.1 will place itself in a “protect”
mode to prevent damage to your speakers. When this happens the power indicator
will turn red and no signal will be heard. You may hear a relay “click” on as the
unit goes into its protection mode.

When this occurs, turn the unit off using the rear panel switch, and correct the
problem. Turn the unit back on. If the unit continues to go into a protect mode,
contact your dealer or installer for assistance.

Troubleshooting Guide

The Citation 5.1 is designed for trouble free operation. In normal use, most users
will not encounter any problems with the unit. However, as with any sophisticated
electronic device, there may be occasional problems on initial installation, or 
during the life of the unit. The items on this list are a brief guide to the minor
problems that you may be able to correct yourself. If these solutions do not rectify
a problem, or if the problem persists, contact your dealer, installer or an authorized
Citation service center for assistance.

21

Problem

Diagnosis

Troubleshooting Hints

Page 

Amplifier will not turn on. Master Power Switch Turned Turn on Master Power 

8, 19

Off. (No Power Light LED)

Switch.

Make certain power cord 

8

is firmly inserted into 
receptacle.

Remote turn-on system not

Check all connections and

8, 9

properly configured. 

switch settings for remote 

(Power Light LED is amber)

system.

Check External Trigger 

9

Device.

Amplifier turns on, but 

Inputs not connected to 

Check Input Connections.

11-16

no audio from one or 

proper jack.

more channels.

Speakers not connected

Check Speaker Connections. 13-18

properly.

Improper settings or output 

Check the settings on your

Consult the

levels from the processor or

preamp, processor or 

manual for

controller.

controller.

the source
device.

Audio plays, then cuts off.

Amplifier Shorted 

Check Speaker connections  13-18

(LED is red)

for short circuit.

Summary of Contents for CITATION 5.1

























Reviews: