Harman Kardon CITATION 5.1 Owner'S Manual Download Page 20

For Automatic Operation:

Make certain that all connections to the Citation Controller or Processor, and to
any other Citation power amplifiers in the system have been correctly made as
shown on pages 13 through 16. Switch the “manual/remote” toggle switch on the
rear panel to the “remote” position. Turn the master power switch ON, position.
The LED below the Citation name will turn amber to indicate that the unit is in
the “standby” mode with AC power applied. 

Your Citation 5.1 amplifier will now turn on automatically whenever the processor or
controller is switched on. You may verify that your amplifier has been turned on in
response to the control signal by noting that the LED below the Citation name will
change from amber to blue. There will be a short second pause between the time the
signal is applied and the indicator changes color until power is applied to the speak-
ers. This pause is intentional, and it protects your speakers from damage as the ampli-
fier stabilizes. You may also hear a relay click as during start-up. This is also normal.

Once your system is turned on, you are ready to enjoy the finest sonic performance
available. There are no controls to adjust on the Citation 5.1 amplifier. All volume
and level adjustments are made by your preamp, controller or surround processor.

There is no need to turn the amplifiers off manually. Simply turn off the Citation
Controller or Processor, or the device providing the automatic control voltages and
the 5.1 amplifier will go into a standby mode. Turn off and return to a standby
mode may be confirmed by noting that the LED indicator under the Citation
name on the front panel turns from blue to amber.

Important Note:  

If you will not be using your audio system for an extended

period of time, such as a vacation, it is always a good idea to turn the unit off
using the rear panel power switch. This will prevent the automatic turn on cir-
cuits from accidentally turning the system on during your absence. 

Service Information

If your installation has followed the suggestions in this manual you should enjoy
many years of trouble-free operation and high quality listening enjoyment. If you
suspect a problem that may require service assistance, contact your dealer, installer
or an authorized Citation Service Depot. The Citation 5.1 does not contain any
user serviceable parts. In the event of a problem, contact your dealer, custom
installer or Madrigal Technical Services at 888-691-4171 (USA Only).

It is important that any repairs be carried out only by an authorized Citation serv-
ice agent to assure proper service and to preserve the protection of your Limited
Warranty. It is a good idea to keep your sales slip or receipt in a safe place with this
manual so that it will be available to verify the purchase date for warranty claims.

Fuse

The Citation 5.1 uses internal fuses to protect both it and your speakers from dam-
age. In the event that a fuse replacement is required, make certain that a fuse of the
original rating is used. Contact an authorized Citation service agent for assistance
with fuse replacement.

20

Summary of Contents for CITATION 5.1

























Reviews: