Harman Kardon AVR 254, Service Manual

Page: 120 / 189

ADV7342/ADV7343
Rev. 0 | Page 18 of 88
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
64
G
ND_I
O
63
CL
KI
N_B
62
S7
61
S6
60
S5
59
S4
58
S3
57
DG
ND
56
V
DD
55
S2
54
S1
53
S0
52
TE
S
T
5
51
TE
S
T
4
50
S_
H
S
YN
C
49
S_
VS
YN
C
47 R
SET1
46 V
REF
45 COMP1
42 DAC 3
43 DAC 2
44
DAC 1
48
SFL/MISO
41
V
AA
40
AGND
39
DAC 4
37 DAC 6
36 R
SET2
35 COMP2
34 PV
DD
33 EXT_LF1
38 DAC 5
2 TEST0
3 TEST1
4 Y0
7 Y3
6 Y2
5
Y1
1
V
DD_IO
8
Y4
9
Y5
10
V
DD
12 Y6
13 Y7
14 TEST2
15 TEST3
16 C0
11 DGND
17
C1
18
C2
19
A
L
SB
/S
PI
_
SS
20
S
DA/
S
CL
K
21
SC
L
/M
O
SI
22 23
P_
H
SY
N
C
24
P_
V
SYN
C
25
P
_
BL
AN
K
26
C4 C3
27
C5
28
C6
29
C7
30
CL
KI
N_A
31 32
PG
N
D
PIN 1
ADV7342/ADV7343
TOP VIEW
(Not to Scale)
EX
T
_
L
F
2
06
39
9-
02
1
Figure 21. Pin Configuration
Table 13. Pin Function Descriptions
Pin No. Mnemonic
Input/
Output
Description
13, 12,
9 to 4 Y7 to Y0 I 8-Bit Pixel Port. Y0 is the LSB. Refer to Table 31 for input modes.
29 to 25,
18 to 16 C7 to C0 I 8-Bit Pixel Port. C0 is the LSB. Refer to Table 31 for input modes.
62 to 58,
55 to 53 S7 to S0 I 8-Bit Pixel Port. S0 is the LSB. Refer to Table 31 for input modes.
52, 51, 15,
14, 3, 2 TEST5 to
TEST0 I Unused. These pins should be connected to DGND.
30 CLKIN_A I Pixel Clock Input for HD Only (74.25 MHz), ED
1
Only (27 MHz or 54 MHz) or SD Only (27 MHz).
63 CLKIN_B I Pixel Clock Input for Dual Modes Only. Requires a 27 MHz reference clock for ED operation or a
74.25 MHz reference clock for HD operation.
50 S_HSYNC I/O SD Horizontal Synchronization Signal. This pin can also be configured to output an SD, ED, or HD
horizontal synchronization signal. See the External Horizontal and Vertical Synchronization
Control section.
49 S_VSYNC I/O SD Vertical Synchronization Signal. This pin can also be configured to output an SD, ED, or HD
vertical synchronization signal. See the External Horizontal and Vertical Synchronization Control
section.
22 P_HSYNC I ED/HD Horizontal Synchronization Signal. See the External Horizontal and Vertical
Synchronization Control section.
23 P_VSYNC I ED/HD Vertical Synchronization Signal. See the External Horizontal and Vertical Synchronization
Control section.
24 P_BLANK I ED/HD Blanking Signal. See the External Horizontal and Vertical Synchronization Control section.
48 SFL/MISO I/O Multifunctional Pin: Subcarrier Frequency Lock (SFL) Input/SPI Data Output. The SFL input is
used to drive the color subcarrier DDS system, timing reset, or subcarrier reset.
47 R
SET1
I This pin is used to control the amplitudes of the DAC 1, DAC 2, and DAC 3 outputs. For full-drive
operation (for example, into a 37.5 Ω load), a 510 Ω resistor must be connected from R
SET1
to
AGND. For low drive operation (for example, into a 300 Ω load), a 4.12 kΩ resistor must be
connected from R
SET1
to AGND.
120
AVR254
harman/kardon