background image

2

2

5

1

6

3

8

9

10

4

7

1.Tape measure

  8. Center punch

2. Tape (slug mount)

  9. File

3. Power drill (screwdriver)

10. Putty knife (slug mount)

4. Drill - 5 mm (

7

/

32

") (slug mount)

11. McLube

®

 Sailkote™ dry lubricant

Drill -

 

4.2 mm (

5

/

32

") (drill/tap)

5. Phillips screwdriver (slug mount)

10-32 or 5 mm tap (drill/tap) – not shown

6. Hammer

Transfer punch 5 mm (

3

/

16

") (drill/tap) – not shown

7. Hacksaw

Mast-up installation:

 stepladder secured to the boat.

Work height:

 2.13 m (7') above boom

11

WARNING!  Strictly follow all instructions to avoid potential hazards that can kill or hurt you  
                    and others. See www.harken.com/manuals for General Warnings and Instructions.

WARNING!  This symbol alerts you to potential hazards that can kill or hurt you and others 
 

if you don't follow instructions. The message will tell you how to reduce the  

 

chance of injury.

This manual gives technical information on installation and service. This information is 

destined exclusively

  

for specialized personnel or expert users. Installation, disassembling, and reassembling by personnel who are  

not experts may cause serious damage to property, injury to users, or injury to those in the vicinity of the product.  

If you do not understand an instruction, contact Harken.

The user must have appropriate training in order to use this product.

Harken accepts no responsibility for damage or harm caused by not observing the safety requirements and  

instructions in this manual. See Limited Warranty, General Warnings, and Instructions at www.harken.com/manuals.

Purpose

Harken Battcars are designed to reduce the size of, or to completely drop the mainsail on a sailboat so wind has little  

effect on the sail. Use of this product for other than normal sailboat applications is not covered by the limited warranty.

Safety Precautions

CAUTION!  This symbol alerts you to potential hazards that can hurt you and others if  
                   you do not follow instructions. The message will tell you how to reduce the  
                   chance of injury.

Tools

McLube is a registered trademark of McGee Industries, Inc. SailKote is a trademark of McLube, a division of McGee Industries.

Summary of Contents for HC7906

























Reviews: