background image

 

System A (CB/slider) 

2

Introduction 

WARNING!  Strictly follow all instructions to avoid potential hazards that may kill or hurt you  
 

and others: www.harken.com/manuals for general warnings and instructions.

WARNING!  This symbol alerts you to potential hazards that may kill or hurt you and others 
 

if you don't follow instructions. The message will tell you how to reduce the  

 

chance of injury.

This manual gives technical information on installation and service. This information is 

written exclusively

 for specialized 

personnel or expert users. Installation, disassembling, and reassembling by personnel who are not experts may cause  

serious damage to property, or injury to users and those in the vicinity of the product. If you do not understand an  

instruction, contact Harken.

The user must have appropriate training in order to use this product.

Harken accepts no responsibility for damage or harm caused by not observing the safety requirements and instructions  

in this manual. See limited warranty, general warnings, and instructions in www.harken.com/manuals.

Purpose

Harken Battcars are designed to reduce the size of, or completely drop the mainsail on a sailboat so wind has little effect 

on the sail. Use of this product for other than normal sailboat applications is not covered by the limited warranty.

Safety Precautions

CAUTION!  This symbol alerts you to potential hazards that may hurt you and others if  
 

you do not follow instructions. The message will tell you how to reduce the  

 

chance of injury.

Summary of Contents for 3811



























Reviews: