I N S T R U C T I O N S
1561/1638 Stand-Up Toggles
Fit Midrange Cars:
1624/1625/1628/1629, T27 Series
Parts List
1
/
4
" (6 mm) Clevis Pin
1. Load plastic bushings from
inside toggle.
Tip:
Slip small screwdriver
into hole and use it as a
guide to insert plastic sleeve.
2. Slip
1
/
4
" (6 mm) clevis pin
through toggle and secure
with small cotter pin.
Install Replacement Bushings (MP-1837)
Install Replacement Polyurethane Stand-Up Device (MP-1838)
Use These Mainsheet Blocks with 1561/1638
Fits Blocks
Single
Double
Triple
Fiddle
A
Post Ø
B
Shackle Pin
Ø
57 mm Carbo
X
X
6 mm
75 mm Carbo
X
6 mm
75 mm Carbo
X
X
5
/
16
" (8 mm)
Small Boat
X
X
7
/
16
" (12 mm)
1
/
4
" (6 mm)
Midrange
X
X
X
X
9
/
16
" (14.5 mm)
5
/
16
" (8 mm)
57 mm ESP Single
X
5
/
16
" (8 mm)
57 mm AirBlock
X
9
/
16
" (14.5 mm)
1
/
4
" (6 mm)
57 mm AirBlock
X
X
5
/
16
" (8 mm)
Use These Car Control Blocks with 1638
Use these Carbo Blocks
End Controls
Purchase
2650 (deadend on control)
X
1631/E2730
2:1
2650 (deadend on block)
X
1632/1633/E2740, E2746
3:1
342/2638 (deadend on control)
X
1632/1633/E2750/E2756
4:1
1. Remove stainless toggle from
car.
Tip:
mark top of toggle to
make installation of new
stand-up device easier.
2. Use pliers to squeeze circular
base of stand-up device; work
device up and out the side.
3. To install replacement piece,
squeeze circular base of
stand-up device and insert
from side of toggle.
Note:
do not use pliers to
squeeze new stand-up device
while installing. This will
damage part.
Tip:
use soap on circular
portion of stand-up device.
Block Swivel Post
13
/
16
"
21 mm
1"
25 mm
1638
13
/
16
"
21 mm
1"
25 mm
B
A
5
/
16
"
8 mm
Large Hole
1
/
4
"
6 mm
Small Hole
1561
Top
Top
Bottom
Bottom
Strictly follow all instructions to avoid an accident, damage to
your vessel, personal injury or death. See www.harken.com/
manuals for additional safety information.
Traveler Cars:
Clean by frequently flushing with fresh water. Periodically clean car by
squirting a detergent/water solution into center openings. Roll car back and forth to
distribute evenly then flush bearings with fresh water.
Do not use spray lubricants because ball bearings may skid not roll. Apply
one to two drops of McLube
®
OneDrop
™
to ball contact surfaces of track.
Roll car back and forth through OneDrop
™
several times to distribute
onto bearings. Wipe remaining OneDrop
™
off track. OneDrop
™
is preferred
but you can also use one to two drops of a light machine oil. Too much oil
attracts dirt.
Track:
Clean with detergent and water.
Important! Exposure to some teak cleaners and other caustic solutions can result
in discoloration of part and is not covered under the Harken warranty.
For additional safety, maintenance and warranty information see www.harken.com/
manuals or the Harken
®
catalog.
Maintenance
Warranty
Inspect
Frequently inspect shackles and control block fittings for signs of fatigue and replace as
necessary. Make sure every installation includes Harken track end stops. Arrange control
tackle so cars do not hit end stops under load.
2
1
3
5
4
5
6
8
7
W15N24983 Bluemound Rd • Pewaukee, WI 53072-4974 USA.
Tel: (262) 691-3320 • Fax: (262) 701-5780
Web: harken.com • Email: [email protected]
No.
Description
Part No.
1561
1 Stand-up toggle
H-17353C
2 Polyurethane stand-up device MP-1838
3
5
/
16
" Clevis pin
HCP208
4
1
/
4
" Clevis pin
HCP211
5 Bushings (2)
MP-1837
6 Large cotter pin
HFS181
7 Small cotter pin
HFS220
8 Blue Loctite
®
833
Loctite
®
is a trademark of Henkel AG & Company KGaA.
McLube
®
is a registered trademark of McGee Industries, Inc.
Printed in USA 4501 11/13
