Hargrove GAS LOGS Installation And Operation Manual Download Page 2

DO NOT USE A NATURAL GAS SET FOR PROPANE OR A PROPANE SET FOR

NATURAL GAS.  WHEN USING PROPANE (LPG) GAS AN AUTOMATIC PILOT SYSTEM 

MUST BE INSTALLED.

1. There are many different local codes for gas fire logs. The installation of this set must conform 

with local codes or, in the absence of local codes, to the National Fuel Gas Code ANSI Z223.1 

1999.

2.

This log set is designed for use with Natural Gas.

3. When glass fireplace doors are used, always operate gas log set with the doors fully open to 

allow for proper combustion air.

4. A fire screen must be in place when the log set is in use.

5. The appliance and its individual shut off valve must be disconnected from the gas supply

piping system at test pressures in excess of 1/2 psig. The appliance must be isolated from the

gas supply piping system by closing its individual manual shut off valve during any pressure

testing of gas supply system at test pressures equal to or less than 1/2 psig.

6. Minimum inlet supply pressure for Natural Gas is 7" water column.  Maximum inlet supply

pressure for Natural Gas is 10 1/2" water column.

7. After burning, the logs become fragile and should not be handled. Knocking or rubbing logs

can cause concrete to crumble and is not covered under the warranty.

8. Use a soft, dry paintbrush for periodic dusting of the gas fire logs.  Special care must be taken 

to clean the Birch logs.  Rubbing will remove soot but will also remove the white pigments.

9.

Do not burn wood with this set

INSTALLING YOUR 

HARGROVE

GAS LOGS

Remove all the parts from the shipping container. Your set includes the following parts...

GENERAL INFORMATION

NOTE

:

GAS LOGS MUST BE INSTALLED BY PERSONNEL QUALIFIED TO INSTALL GAS APPLIANCES.

Number by Set

16”-21” Sets

24” Sets

28”-30” Sets

36” Sets

1. Pedestal Gate

P G – 1 6

P G – 2 0

P G – 2 5

P G – 3 0

2. Ember Burner

E B -1 4

E B – 1 8

E B – 2 2

E B – 2 6

3. Silica Sand

( 1 ) S D - 8

( 1 )  S D – 1 0

( 1 ) S D - 1 2

( 2 ) S D – 8

4. Fire Embers

E M

E M

E M

( 2 ) E M

5. Safety Pilot Control (optional)

S P C / C P C

S P C / C P C

S P C / C P C

S P C / C P C

6. Aluminum Connector

A C – 1 8

A C – 1 8

A C – 1 8

A C – 1 8

7. Fire Logs

* Number of logs determined by set size

8. Damper Stop (optional)

D S

D S

D S

D S

9. Volcanic Cinders

V C

V C

V C

( 2 ) V C

Summary of Contents for GAS LOGS












Reviews: