Step 5.
To remove the mounting feet use a finger on the clip and gen-
tly pull up on the tab.
NOTE:
For Remote Display installation please see Chapter 3,
Installation, of the HI 4060 User’s Guide.
LOAD POINT INSTALLATION
FIG. 5 REAR PANEL
FIG. 6
C2
®
Load Point Connection
Cable color Code for C2 Load Points (left to right facing the rear panel):
•
Shield
Ground Wire
•
C2-
Violet
•
C2+
Grey
•
EXC-
Black
•
SEN-
Brown
•
SIG-
White
•
SIG+
Green
•
SEN+
Blue
•
EXC+
Red
Step 1.
Remove the factory installed jumpers from the terminal block
if you are connecting an 8 wire cable from the junction box.
(See Fig. 8)
Step 2.
Connect the cable (Recommended load cell cable: Hardy
Instruments Prt. # 6020-0001) wires to the Channel terminal
block according to the cable color chart.
Step 3.
Plug the terminal block into the Channel connector on the rear
panel.
Step 4.
For more information concerning C2 Load Point connection,
consult the HI 4060 User Guide.
Non-C2 Load Point Connection
NOTE:
Cable Color Codes vary between vendors, check with your
supplier for the Color Code for your Non-C2 load point. Do
not connect wires to the -C2 and +C2.
Step 1.
Remove the factory installed jumper from the terminal block if
you have 6 wire load cell cable that includes sense wires from
the load cell or junction box.
Step 2.
Connect the cable (Recommended load cell cable: Hardy
Instruments Prt. # 6020-0001) wires to the Channel 1 terminal
block according to the Non-C2 cable color chart, or per manu-
facturers specification.
Step 3.
Plug the terminal block into the Channel connector on the rear
panel.
INPUT POWER WIRING
WARNING: D
O
NOT
PLUG
THE
POWER
CONNECTOR
INTO
THE
HEADER
WITH
LIVE
POWER
. T
O
DO
SO
WILL
RESULT
IN
PROP
-
ERTY
DAMAGE
AND
/
OR
PERSONAL
INJURY
.
WARNING:
IF
A
LITHIUM
BATTERY
IS
REPLACED
WITH
AN
INCORRECT
TYPE
IT
MAY
CAUSE
AN
EXPLOSION
WHICH
WILL
CAUSE
PROPERTY
DAMAGE
OR
PERSONAL
INJURY
.
AC Input Power Wiring (-AC)
WARNING:
DO
NOT
OPERATE
WITH
INCORRECT
LINE
VOLT
-
AGE
.
TO
DO
SO
WILL
RESULT
IN
PROPERTY
DAMAGE
AND
/
OR
PERSONAL
INJURY
. M
AKE
SURE
THAT
THE
POWER
SOURCE
DOES
NOT
EXCEED
240 VAC.
WARNING: I
F
AN
AUTOMATIC
DISCONNECT
DEVICE
IS
USED
ON
THE
AC
INPUT
WIRES
,
THE
DISCONNECT
MUST
ACT
ON
BOTH
THE
LINE
AND
NEUTRAL
WIRES
IN
A
DOUBLE
POLE
,
DOU
-
BLE
THROW
ARRANGEMENT
I
.
E
. DPDT R
ELAY
. U
SING
OTHER
AUTOMATIC
DISCONNECT
ARRANGEMENTS
MAY
CAUSE
PER
-
SONAL
INJURY
AND
/
OR
PROPERTY
DAMAGE
.
•
The AC power should be supplied by a “clean” pri-
mary line, directly from the power panel. This line
should not supply any other equipment, including
the feeding unit, and should be supplied with a mini-
mum 10 amp breaker.
•
AC Power Input (See Fig. 7)
Neu (Low)
Line (HI)
Earth Ground
Step 1.
The HI 4060 is configured with a universal power supply rated
from 110 to 240 VAC.
Step 2.
Make sure the VAC power is shut off before installing the
wires to the connector.
Step 3.
Install a 3-wire, minimum 14 AWG power line to the 3-pin ter-
minal block connector.
Relay Outputs
Analog Inputs
Digital Inputs
Control
Output
Relay Outputs
Analog Inputs
Digital Inputs
Control
Output
