manualshive.com logo in svg

Hardy Process Solutions HI 1756-FC, User Manual

Share
Download
Hardy Process Solutions HI 1756-FC User Manual Download Page 16

 
 

11 

 

●

●

●

●

●

 

Chapter 4 

 

Chapter 4 Configuration 

●

 

●

 

●

 

●

 

●

 

 

Chapter 4 covers the settings used to prepare the controller for calibration and operation. 
The Setup procedures require Allen-Bradley’s RS Logix 5000, Allen-Bradley RSLinx™ 
or RSLinx™ Lite. 

Power Check 

To make or change settings, there 
must be power to both the PLC and 
the module. Verify that the LEDs 
are lit for normal operation.  

 

 

 

 

Module LEDs 

LEDS 

Scale Data LEDs 

Flashing Green  

Feeder is on

 

Steady Green Running  

(Normal) 

Steady Red  

Error Read Failure or Error eeprom write. Contact HI 
Customer Support 

Flashing Red  

Read Convert Error. 

LED is Off 

Channel is Inactive 

OK Module Status LED 

Brief Steady  

During power up the LED lights Red for about one second. 

Flashing Green 

In Program mode. (Normal) 

Steady Green 

In Run Mode. (Normal) 

Steady Red 

Config. Fault The eeprom checksum failed - bad serial 
eeprom 

(Backplane Available) 

data or blank serial eeprom. Contact HI Customer Support. 

Steady Red 

Internal Hardware watchdog timer fault (e.g. bad Hardware 
or Firmware). ASIC is non-operational. 

Flashing Red 

Communication Error. 

 

 

Summary of Contents for HI 1756-FC

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands