Hardinge SERIES I Installation Operation & Maintenance Download Page 8 | Manualshive

Page: 8 / 23

background image

HI-NEUTRAL-LO LEVER

The Hi-Neutral-Lo Lever “O”, Figure 2.13, is used to put the attachment into either back gear or

direct drive. Rotate the spindle by hand to facilitate meshing of clutch or gears.

Neutral is provided to permit free spindle rotation for indicating and setup work.

In the high speed position (direct drive) the spindle is driven by tapered clutch teeth. If the clutch is

not meshed tightly, clutch rattle will be heard. This can be corrected by loosening the two securing
screws in lever while in high speed position. The clutch spring will automatically adjust the clutch.
Tighten the two securing crews in lever.

- CAUTION -

Do not shift hi-lo lever while motor is running.

M-450

2-7

Figure 2.13 - Hi-Neutral-Lo Lever

Neutral

High

Low

Securing Screws

TP5297

O

«
...
6
7
8
9
10
...
»

Summary of Contents for SERIES I
























Reviews:

No comments

Related manuals for SERIES I

Brand: FAR Pages: 44

Brand: FAR Pages: 28

Brand: FAR Pages: 32

Brand: FAR Pages: 24

Brand: FAR Pages: 68

Brand: FAR Pages: 8

Brand: Lambda Pages: 56

Brand: Lakeshore Pages: 122

Brand: CAMPAGNOLA Pages: 66

Brand: Tone Pages: 28

Brand: Agilent Technologies Pages: 142

Brand: Campbell Hausfeld Pages: 16

Brand: SMC Networks Pages: 2

Brand: HARDELL Pages: 8

Brand: Lux Tools Pages: 36

Brand: Yokota Pages: 9

ASye 636 Kinetik

Brand: Fein Pages: 77

Brand: Rapid Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands